Reliability engineer jobs in Centereach, New YorkCreate job alerts

Our client is seeking a motivated and detail-oriented Senior Electrical Engineer to join our engineering team. This senior position is ideal for an engineer who enjoys working across the full product lifecycle—from concept and design through validation and production—while contributing to high-reliability power electronics solutions used in demanding environments such as aerospace, defense, and industrial systems. \n \n \n \n Job Function: \n Key Responsibilities \n\n • Design, develop, and test analog and power electronic circuits, including AC-DC and DC-DC conversion systems\n, • Good understanding of DSP based power electronic products, experience in product development / troubleshooting\n, • Experience in Digital Vector based control of BLDC motors, MATLAB and Simulink would be an asset\n, • Perform component selection, schematic capture, and PCB layout activities with attention to EMI, thermal performance, and reliability\n, • Conduct circuit simulation (e.g., SPICE-based tools) and analyze performance under varying electrical and environmental conditions\n, • Develop and execute validation and qualification test plans, including worst-case analysis and derating\n, • Troubleshoot hardware issues at the board and system level, including root cause analysis and corrective action implementation\n, • Collaborate with cross-functional teams including mechanical engineering, manufacturing, and quality assurance\n, • Support transition from prototype to production, including documentation, test procedures, and manufacturing support\n, • Participate in design reviews and contribute to continuous improvement of engineering processes\n, • Heavy interaction with customers to support product development opportunities\n\n \n \n Job Requirement: \n Required Qualifications \n\n • Bachelor’s degree in electrical engineering or related field\n, • 7–10 years of relevant industry experience\n, • Strong foundation in analog circuit design and power electronics\n, • Experience with schematic capture and PCB layout tools (e.g., Altium or similar)\n, • Experience with lab equipment such as advanced oscilloscopes with optical probes, spectrum analyzers, and power analyzers\n, • Working knowledge of EMI/EMC principles and mitigation techniques\n, • Ability to debug circuits and systems methodically and able to work independently\n, • Strong written and verbal communication skills\n\n \n Preferred Qualifications \n\n • Experience designing high-reliability applications (e.g., aerospace, military, or medical)\n, • Familiarity with industry standards such as MIL-STD or IPC guidelines\n, • Experience with thermal analysis and magnetic component selection\n, • Exposure to digital control of power converters (e.g., microcontrollers or DSPs)\n, • Understanding of isolation techniques and high-voltage design considerations\n, • Experience developing embedded firmware and/or PC-based tools (e.g., C/C++, Python, or C#), including simple GUI applications for test, control, or data visualization\n\n \n

Job Description Job Location: Hauppauge NY Narda-MITEQ is dedicated to recruiting and developing diverse, high-performing talent who are passionate about what they do. Our employees are unified in a shared dedication to our customers’ mission and quest for professional growth. Narda-MITEQ provides an inclusive, engaging environment designed to empower employees and promote work-life success. Fundamental to our culture is an unwavering focus on values, dedication to our communities, and commitment to excellence in everything we do. Narda-MITEQ designs and manufactures an extensive range of standard active and passive components, as well as custom subsystems and integrated microwave assemblies to meet the requirements found on land, sea, air and the harsh environment of space. Our global customers rely on our deep technical expertise and innovation grounded in more than 70 years of experience to help them meet the challenges of their next-generation military and commercial applications. The following statements are intended to describe the general nature and level of work being performed. They are not intended to be an exhaustive list of all essential functions, duties, or skills required for this role. Management retains the discretion to add or change the duties at any time. Job Description: We are seeking a motivated and collaborative Software Engineer to join our team and help develop software solutions that support a wide variety of business needs across the organization. This role offers the opportunity to work on meaningful projects, collaborate with technical and cross functional teams, and contribute to the ongoing improvement of our applications and development processes. The ideal candidate is a problem solver who enjoys developing efficient, scalable software, writing clean and maintainable code, and working in a collaborative environment. In addition to software development, this position will participate in testing, documentation, troubleshooting, and process improvement initiatives that help drive operational excellence. Essential Functions: • Design, develop, test, and maintain software applications that support a variety of business needs., • Develop applications using Microsoft Visual Studio with strong programming skills in Visual Basic .NET and C# programming., • Utilize Microsoft SQL Server database design, administration and application support., • Create and optimize SQL stored procedures, queries, and Transact-SQL scripts to ensure efficient data management and application performance., • Participate in software testing, debugging, and verification activities to ensure quality and reliability of applications., • Write clean, concise, well-documented code that is easy to maintain and understand by other developers., • Collaborate with software engineers, IT professionals, and business users to develop and enhance software solutions., • Create and maintain technical documentation, operating procedures, and software specifications., • Develop reports and dashboards using Microsoft Power BI to support business intelligence and decision-making., • Work within or integrate with ERP systems and understand how software solutions support broader business operation., • Participate in Agile development methodologies and contribute to continuous improvement of development practices., • Knowledge of AutoCAD and its application within engineering or manufacturing environments a plus., • Assist in identifying opportunities to improve processes, streamline workflows and increase organizational efficiency. Qualifications: • Minimum 4 years professional software development experience., • Bachelor’s degree in Computer Science, Information Systems, or related technical field. Equivalent practical experience may be considered., • Strong programming experience with Visual Basic .NET and C#., • Strong experience with Microsoft SQL Server, including database design, stored procedures and T-SQL development., • Experience developing, testing, and maintaining business applications., • Understanding of ERP systems and business process integration preferred., • Experience working in an Agile software development environment., • Strong Analytical, troubleshooting, and problem-solving skills., • Ability to work both independently and collaboratively in a team environment. Preferred Additional Skills: • Microsoft SQL Server Certification is a plus., • Strong written and verbal skills, • Excellent organizational skills and the ability to manage multiple projects and priorities., • Experience with Microsoft Power BI and business reporting tools., • Familiarity with Windows operating systems, user permissions, and security concepts. Please be aware that many of our positions require the ability to obtain a security clearance. Security clearances may only be granted to U.S. citizens. In addition, applicants who accept a conditional offer of employment may be subject to government security investigation(s) and must meet eligibility requirements for access to classified information. Narda-MITEQ is proud to be an Equal Opportunity/Disability/Veterans Employer. We are committed to maintaining a workplace that is inclusive, respectful, and free from discrimination, where all employees and applicants are treated with dignity and fairness. Employment decisions are made in accordance with applicable federal, state, and local laws. All qualified applicants receive equal consideration without regard to race, color, religion, sex (including pregnancy, childbirth, breastfeeding, or related medical conditions), sexual orientation, gender identity or expression, age, national origin, marital status, citizenship status, disability, protected veteran status, or any other characteristic protected by law. Narda-MITEQ complies with applicable Executive Orders, including affirmative action requirements for individuals with disabilities and veterans. Narda-MITEQ is a drug-free workplace and conducts pre-employment substance abuse testing and background checks, as permitted by law. If you are a qualified individual with a disability or a disabled veteran and require a reasonable accommodation to use or access the Narda-MITEQ career website due to your disability, you have the right to request such an accommodation. To request a reasonable accommodation, please contact Denise Nocerino at denise.nocerino@nardamiteq.com. Proof of employment authorization will be required. Narda-MITEQ is not required to sponsor applicants for work visas. As this position will require access to export-controlled information, only applications from “U.S. persons” within the meaning of the International Traffic in Arms Regulations and Export Administration Regulations will be considered. Narda-MITEQ is not required to seek export license for applicants who do not meet this requirement

Job Description For more than 60 years, Power Device Corporation (PDC) has been recognized as a world leader in the design and manufacture of high-reliability Connectivity, Power, and Control solutions for the Aerospace, Defense, and Space industries. Our dedication to supplying quality products, on-time delivery, and superior support, has contributed to the success of our customers and the critical missions they serve. This position is 100% onsite at our Bohemia, NY location. The compensation for this role is $90,000 - $120,000 annual based on experience. This position requires a U.S Person or a person who can qualify for a Department of State or Department of Commerce License. Position Summary: To continue to meet our customer’s mission critical needs, PDC is seeking an Analog/Mixed Signal Design Engineer to join our dynamic, growing organization as a valued member of our team. The candidate needs experience in developing devices with active / passive signal converter & conditioning circuits and switching power control / driver circuits; designs are implemented either as a multi-chip & wire hermetically-sealed hybrids, or as SMT Circuit Card Assemblies (CCA’s). Responsibilities • Key role: Take primary technical leadership in the design and support of our Synchro / Resolver to Digital, DATEL A2D & D2A mixed signal converter product lines, and our switched-mode multi-phase Brushless DC Motor (BLDC) driver & controller product lines. This requires a deep understanding of analog / mixed signal analysis and design techniques to ensure device specifications are met with robust margin. You will guide an interdisciplinary Engineering team through the phases of product life cycle development from requirements, architecture, & detailed design, through to device verification, qualification, and manage the transition to production. Our legacy models require continuous obsolescence review and at times may need redesign to support our mil- aero customer base. Requirements • Bachelor’s degree in Electrical Engineering; Graduate Engineering degree a plus., • 3- 7 minimum years of experience, • Deep bench of Analog Circuit design experience in multiple A to D architectures (multiple pass SAR, Flash, Sigma Delta, Pipeline) and D to A (serial DACs, R2R, current steering, charge scaling). Experience should cover low noise and high dynamic range techniques, sample acquisition and hold circuits, Bandgap reference, Oscillators, Op-amps, Switched Capacitor Circuits, Active Filters, single ended & differential circuits, phase / frequency control loops and stability analysis. Comfort working both time & frequency domains a plus., • Experience in power electronics / power management (Buck/Boost, LDO, Charge Pump, Inverters using MOSFET, IGBT, SiC and GaN Power devices., • Analog / mixed signal ASIC design and verification using Cadence or Tanner tool suites., • Experience with space-level radiation tolerant / hardened design, rad lot testing, ionizing radiation, single event upset and total dose analysis regarding component selection., • Sensors, including LVDT, Synchro / Resolvers and Encoders., • Control theory and Matrix mathematics including Z domain transform for digital control; Experience with Motor control simulation, • Clark and Park transform theory, • High level understanding of thermal, electrical stress, worst case, FMEA, tolerance, aging, and design for low EMI., • Experience with CAD tools such as LT-Spice, P-Spice, OrCAD, Allegro, PADS., • Candidate must be a US Citizen, Permanent Resident or Green Card Holder due to Export control laws. Essential Duties: • Develop clear requirements and specs from marketing / customer documents., • Provide early customer interaction to guide requirements toward more realizable product., • Distill large-scale designs down to their architectural elements, and develop unique, innovative analog and digital hardware design solutions. Consider & pursue patent application for differentiators that will help secure competitive advantage., • Generate reports and present findings to the team throughout the review process. Facilitate DFM by coordinating teams of varied technical disciplines through a clearly defined design process. Co-ordinate technical reviews with other groups., • Develop creative approaches that favorably optimize complex design tradeoffs for product cost, performance, feature set, time to market, and technical risk. Anticipate potential difficulties and develop alternative plans., • Manage support and verification activities (thermal, electrical stress, worst-case, FMEA, tolerance, aging, and EMI analyses, performance simulations, and design verification) to ensure meeting all environmental requirements for the application., • Develop project plans, budgets, schedules, and identify the resources to progress from market requirement through product release. Identify risks and develop contingency plans to mitigate schedule / technical threats to the program., • Contribute technical input, as well as material and labor cost estimates in support of winning tactical business opportunities and proposals., • Mentor, coach, and train engineers to facilitate greater levels of technical and professional achievement., • Support legacy product lines and resolve new product issues as they arise., • Work across departments to lead vendor or engineering outsource selection decisions based on technical performance, risk and cost tradeoffs., • Take the initiative to investigate and propose new method, process, technique, tool, component, or technology improvements for quality, timeliness, and efficiency., • Conduct in-depth technical interviews and make hiring recommendations for capable and talented technical staff to grow an effective Engineering team.

Job Description Position: Sr. Electrical Design Engineer / Project Engineer III Location: Bohemia, New York Overview: We are seeking a highly skilled Electrical Design Engineer with a strong foundation in electrical and power supply concepts, combined with hands-on experience in designing and optimizing power supply systems. The ideal candidate will have a solid theoretical background in electrical engineering, specifically in power supply design, and experience with designing for manufacturing. Key Responsibilities: • Apply a strong theoretical background in Electrical/Power Supply Concepts to design and develop power supply systems that meet the required specifications and standards., • Design for Manufacturing (DFM): Ensure all designs are optimized for ease of manufacturing, considering cost, scalability, and quality control., • Utilize hands-on experience in electrical power supply design to innovate, troubleshoot, and refine power supply products. Qualifications: • Bachelor’s degree in electrical engineering or a related field., • 5-10 years of hands-on experience in power supply electrical design, • Thermal system design for power supply, • Knowledge of safety and reliability standards for power conversion devices, • Knowledge in firmware programming a plus, • Knowledgeable in simulation, computation program is a plus, • Manufacturing best practices knowledge is a plus Benefits: • 401(k), • 401(k) matching, • Dental insurance, • Health insurance, • Life insurance, • Paid time off, • Vision insurance

Job Description iRocket (Innovative Rocket Technologies Inc.) is pioneering fully autonomous, fully reusable small launch vehicles for responsive access to space. We leverage cutting-edge propulsion, reuse, and sustainable propellant technologies to make launch more frequent, lower cost, and eco-friendly. We are headquartered in New Hyde Park, NY. The Role As a Machining & Manufacturing Engineer at iRocket, you will own the development, optimization, and scaling of high-precision manufacturing processes for rocket hardware. You will work cross-functionally with design, test, supply chain, and quality teams to mature processes from prototype through production. You will report to the Senior Manager of Manufacturing Engineering. • Develop, validate, and refine machining processes (CNC turning, milling, EDM, grinding, etc.) for rocket components, • Collaborate with design engineers to ensure manufacturability, offer design for manufacturing (DFM) feedback, and propose design changes where beneficial, • Create and maintain manufacturing BOMs, process flows, work instructions, and SOPs, • Support installation, calibration, qualification, and commissioning of new machines and tooling, • Lead root cause analysis (RCA) for production issues and drive corrective and preventive actions, • Implement process controls, error-proofing, statistical monitoring, and quality gates, • Participate in manufacturability reviews and design reviews to provide input from a manufacturing perspective, • Document and drive continuous improvement in process maturity, standardization, and scaling, • Support aerospace / defense compliance efforts (e.g. AS9100, aerospace quality standards), • Occasionally support mission-critical deadlines which may require non-standard hours Requirements • Bachelor’s degree in Mechanical Engineering, Manufacturing Engineering, or a related discipline, • 3+ years of experience in machining / manufacturing engineering in aerospace, defense, or precision industries, • Strong knowledge of GD&T, tolerancing, fixtures, tooling, materials, machining best practices, • Hands-on experience developing machining processes, tooling, fixturing, • Proficiency in reading engineering drawings, specifications, and technical documentation, • Ability to work cross-functionally, strong problem solving, and data analysis skills, • Excellent communication skills (verbal and written), • Master’s degree in Mechanical or Manufacturing Engineering, • Experience with aerospace quality systems (AS9100, NADCAP, etc.), • Familiarity with additive manufacturing, welding, exotic materials, or hybrid manufacturing methods, • Experience with lean manufacturing, continuous improvement methodologies (Six Sigma, Kaizen), • Proficiency in CAD/CAM or manufacturing software (e.g. NX, SolidWorks, Mastercam, etc.), • Experience in propulsion, space, or high-reliability systems Benefits • Health Care Plan (Medical, Dental & Vision), • Retirement Plan (401k, IRA), • Life Insurance (Basic, Voluntary & AD&D), • Paid Time Off (Vacation, Sick & Public Holidays), • Family Leave (Maternity, Paternity), • Short Term & Long Term Disability, • Wellness Resources

Job Description iRocket is developing fully autonomous, fully reusable small launch vehicles to provide responsive, cost-effective access to space. Our mission is to catalyze a new era of space exploration through innovation in propulsion, structures, and sustainable launch systems. The Role: We are seeking a Mechanical Engineer to contribute to the design, development, and transition of mechanical components and systems from development through production. You’ll partner with propulsion, manufacturing, integration, and test teams to help deliver high-performance, reliable rocket hardware. • Act as Responsible Engineer for key subsystems or components (e.g., valves, mechanical assemblies), • Advance design of parts and assemblies: create CAD models, drawings, and associated documentation, • Perform mechanical analyses, calculations, and design iterations to meet performance, mass, and reliability targets, • Collaborate with manufacturing teams to ensure designs are manufacturable, and iterate designs based on feedback, • Support fabrication, post-processing, inspection, and tolerance verification of parts, • Assist with integration, assembly, and test of mechanical and propulsion subsystems, • Create schematics, document design and manufacturing processes, and maintain records, • Participate in test campaigns, support troubleshooting, and analyze results, • Communicate progress, issues, and tradeoffs clearly across cross-functional teams, • Ensure safe practices and adherence to PPE and safety standards in lab, shop, and test areas Requirements • Bachelor’s degree in Mechanical Engineering or a related engineering discipline, • 3+ years of experience in mechanical design, development, fabrication, assembly, or test, • Proficiency in CAD, • Knowledge of GD&T, tolerance design, part and assembly drawings, • Strong problem solving, analytical thinking, and collaboration skills, • Excellent written and verbal communication skills, • Ability to manage multiple tasks in a fast-paced environment, • Experience in aerospace, propulsion, or high-reliability systems, • Hands-on engineering background (design to bench to manufacturing), • Experience with simulation or analysis tools (e.g. ANSYS, FEA), • Experience scripting or using tools such as MATLAB or Python, • Comfort iterating quickly, learning from experiments, and working through ambiguity Benefits • Health Care Plan (Medical, Dental & Vision), • Retirement Plan (401k, IRA), • Life Insurance (Basic, Voluntary & AD&D), • Paid Time Off (Vacation, Sick & Public Holidays), • Family Leave (Maternity, Paternity), • Short Term & Long Term Disability, • Wellness Resources

Job Description Position Title: Quality Engineer Intern For more than 60 years, Power Device Corporation (PDC) has been recognized as a world leader in the design and manufacture of high-reliability Connectivity, Power, and Control solutions for the Aerospace, Defense, and Space industries. Our dedication to supplying quality products, on-time delivery, and superior support, has contributed to the success of our customers and the critical missions they serve. This position is 100% onsite at our Bohemia, NY location. The compensation for this role is $20 - $25 hourly a is a 6 month temporary position. This position requires a U.S Person or a person who can qualify for a Department of State or Department of Commerce License. Position Summary: We are seeking a motivated and detail-oriented Quality Engineering Intern to join our Quality team. This internship provides hands-on experience supporting an AS9100-certified Quality Management System within a high-reliability manufacturing environment. The successful candidate will work alongside Quality Engineers, Process Engineers, and Operations personnel to improve product quality, investigate manufacturing issues, and support customer and regulatory requirements. This is an excellent opportunity for engineering or technical students interested in aerospace, manufacturing, quality systems, and continuous improvement. Key Position Accountabilities: • Support Quality Engineers with day-to-day quality assurance and manufacturing activities., • Assist in investigating product and process nonconformances using Root Cause and Corrective Action (RCCA) methodologies., • Participate in the preparation, tracking, and closure of Corrective Action Requests (CARs) and verify implementation of corrective actions., • Review manufacturing records, inspection results, and test data for completeness and compliance., • Prepare and organize End Item Data Packs for customer deliveries, ensuring all required quality documentation is complete and accurate., • Assist with calibration program activities, including reviewing calibration status, updating records, and helping maintain measurement equipment compliance., • Analyze manufacturing and inspection data to identify trends, recurring issues, and opportunities for process improvement., • Support First Article Inspection (FAI) activities in accordance with AS9102., • Assist with internal audits and verification of compliance to AS9100 procedures and work instructions., • Participate in Material Review Board (MRB) activities by collecting data and supporting disposition documentation., • Review supplier documentation including Certificates of Conformance, inspection reports, and quality records., • Help maintain quality metrics, dashboards, and reports for management review., • Collaborate with Engineering, Manufacturing, Supply Chain, and Inspection teams on quality improvement initiatives., • Perform additional quality engineering projects as assigned. Required Knowledge, Skills and Abilities: • Strong analytical and problem-solving abilities., • Excellent organizational skills and attention to detail., • Ability to interpret technical drawings and engineering documentation., • Proficiency with Microsoft Excel, Word, and PowerPoint., • Comfortable working with data and identifying trends., • Strong written and verbal communication skills., • Ability to work independently while collaborating effectively within a cross-functional team., • Eagerness to learn aerospace quality standards and manufacturing processes. Qualifications: • Currently pursuing a degree in:, • Mechanical Engineering, • Electrical Engineering, • Industrial Engineering, • Manufacturing Engineering, • Quality Engineering, • Engineering Technology, • or a related STEM discipline, • Rising junior, senior, or graduate student preferred. Why Join Us? This internship offers meaningful, real-world engineering experience where your work directly supports the manufacture of high-reliability aerospace products. You'll collaborate with experienced engineers and quality professionals, gain exposure to industry standards, and build skills that translate directly into careers in aerospace, defense, medical device, automotive, and advanced manufacturing. This job description is not designed to cover or contain a comprehensive listing of activities, duties or responsibilities that are required of the employee. This job description indicates, in general the nature and levels of work, knowledge, skills, abilities and other essential functions (as covered under the ADA) expected of the incumbent. Duties, responsibilities and activities may change at any time with or without notice as required. Power Device Corporation is an Affirmative Action/Equal Opportunity Employer and is committed to providing equal employment opportunity (EEO) for all persons in all facets of employment. All qualified applicants will receive consideration for employment without regard to race, color, religion, age, gender, sexual orientation, gender identity, national origin, citizenship status, marital status, genetic information, disability, protected veteran status or any other legally protected status.

Job Description iRocket (Innovative Rocket Technologies Inc.) is pioneering fully autonomous, fully reusable small launch vehicles to enable responsive, lower-cost access to space. We combine advanced propulsion, reuse, and sustainable propellant technologies to push the frontier of commercial space. The Role: We are seeking a Propulsion Engineer to join our propulsion team and contribute to the design, development, testing, and qualification of propulsion systems for our launch vehicles. You will work closely with integration, test, design, and manufacturing teams to bring propulsion systems from concept to flight readiness. • Support design, development, and testing of propulsion systems (e.g. liquid rocket engines, pressure-fed or pump-fed systems, component-level systems), • Participate in test campaigns, including planning, instrumentation, execution, and post-test analysis, • Develop and maintain test procedures, control sequences, and configuration files for propulsion testing, • Troubleshoot issues in propulsion subsystems (fluid, mechanical, thermal) during testing and integration, • Collaborate with cross-functional teams (mechanical, thermal, controls, electronics, systems) to ensure subsystem integration, • Perform calculations and simulations to support sizing, performance prediction, and optimization, • Support Test Readiness Reviews (TRRs), Failure Review Boards, and design reviews, • Implement continuous improvements to increase test efficiency, safety, and reliability, • Analyze test data, generate reports, and identify corrective actions Requirements • Bachelor’s degree in Aerospace Engineering, Mechanical Engineering, or a related discipline, • 2+ years of experience in propulsion, test, or fluid/thermal systems development and testing, • Familiarity with liquid or hybrid rocket engine systems, fluid dynamics, thermodynamics, and heat transfer, • Experience with instrumentation, sensors, data acquisition, control systems, • Proficiency with scripting or programming (Python, MATLAB, etc.), • Ability to read and interpret engineering drawings, P&IDs, and technical specifications, • Strong problem-solving, data analysis, and communication skills, • Ability to work in multidisciplinary teams and in a fast-paced, evolving environment, • Experience with cryogenic fluids, high-pressure systems, or oxidizer/fuel systems, • Experience with CAD, simulation tools (CFD, thermodynamics, structural), or propulsion modeling, • Familiarity with propulsion test stands, plumbing, valve systems, or turbomachinery, • Experience in space, launch vehicle, or high-reliability systems, • Experience in formal test planning, instrumentation, and control software Benefits • Health Care Plan (Medical, Dental & Vision), • Retirement Plan (401k, IRA), • Life Insurance (Basic, Voluntary & AD&D), • Paid Time Off (Vacation, Sick & Public Holidays), • Family Leave (Maternity, Paternity), • Short Term & Long Term Disability, • Wellness Resources

Job Description For more than 60 years, Power Device Corporation (PDC) has been recognized as a world leader in the design and manufacture of high-reliability Connectivity, Power, and Control solutions for the Aerospace, Defense, and Space industries. Our dedication to supplying quality products, on-time delivery, and superior support, has contributed to the success of our customers and the critical missions they serve. This position is 100% onsite at our Bohemia, NY location. The compensation for this role is $120,000 - $160,000 annually based on experience. This position requires a U.S Person or a person who can qualify for a Department of State or Department of Commerce License. Position Summary: To continue to meet our customer’s mission critical needs, PDC is seeking an Analog/Mixed Signal Design Engineer to join our dynamic, growing organization as a valued member of our team. The candidate needs experience in developing devices with active / passive signal converter & conditioning circuits and switching power control / driver circuits; designs are implemented either as a multi-chip & wire hermetically-sealed hybrids, or as SMT Circuit Card Assemblies (CCA’s). Responsibilities: • Key role: Take primary technical leadership in the design and support of our Synchro / Resolver to Digital, DATEL A2D & D2A mixed signal converter product lines, and our switched-mode multi-phase Brushless DC Motor (BLDC) driver & controller product lines. This requires a deep understanding of analog / mixed signal analysis and design techniques to ensure device specifications are met with robust margin. You will guide an interdisciplinary Engineering team through the phases of product life cycle development from requirements, architecture, & detailed design, through to device verification, qualification, and manage the transition to production. Our legacy models require continuous obsolescence review and at times may need redesign to support our mil- aero customer base. Requirements: • Bachelor’s degree in Electrical Engineering; Graduate Engineering degree a plus., • 7+ minimum years of experience, • Deep bench of Analog Circuit design experience in multiple A to D architectures (multiple pass SAR, Flash, Sigma Delta, Pipeline) and D to A (serial DACs, R2R, current steering, charge scaling). Experience should cover low noise and high dynamic range techniques, sample acquisition and hold circuits, Bandgap reference, Oscillators, Op-amps, Switched Capacitor Circuits, Active Filters, single ended & differential circuits, phase / frequency control loops and stability analysis. Comfort working both time & frequency domains a plus., • Experience in power electronics / power management (Buck/Boost, LDO, Charge Pump, Inverters using MOSFET, IGBT, SiC and GaN Power devices., • Analog / mixed signal ASIC design and verification using Cadence or Tanner tool suites., • Experience with space-level radiation tolerant / hardened design, rad lot testing, ionizing radiation, single event upset and total dose analysis regarding component selection., • Sensors, including LVDT, Synchro / Resolvers and Encoders., • Control theory and Matrix mathematics including Z domain transform for digital control; Experience with Motor control simulation, • Clark and Park transform theory, • High level understanding of thermal, electrical stress, worst case, FMEA, tolerance, aging, and design for low EMI., • Experience with CAD tools such as LT-Spice, P-Spice, OrCAD, Allegro, PADS., • Candidate must be a US Citizen, Permanent Resident or Green Card Holder due to Export control laws. Essential Duties: • Develop clear requirements and specs from marketing / customer documents., • Provide early customer interaction to guide requirements toward more realizable product., • Distill large-scale designs down to their architectural elements, and develop unique, innovative analog and digital hardware design solutions. Consider & pursue patent application for differentiators that will help secure competitive advantage., • Generate reports and present findings to the team throughout the review process. Facilitate DFM by coordinating teams of varied technical disciplines through a clearly defined design process. Co-ordinate technical reviews with other groups., • Develop creative approaches that favorably optimize complex design tradeoffs for product cost, performance, feature set, time to market, and technical risk. Anticipate potential difficulties and develop alternative plans., • Manage support and verification activities (thermal, electrical stress, worst-case, FMEA, tolerance, aging, and EMI analyses, performance simulations, and design verification) to ensure meeting all environmental requirements for the application., • Develop project plans, budgets, schedules, and identify the resources to progress from market requirement through product release. Identify risks and develop contingency plans to mitigate schedule / technical threats to the program., • Contribute technical input, as well as material and labor cost estimates in support of winning tactical business opportunities and proposals., • Mentor, coach, and train engineers to facilitate greater levels of technical and professional achievement., • Support legacy product lines and resolve new product issues as they arise., • Work across departments to lead vendor or engineering outsource selection decisions based on technical performance, risk and cost tradeoffs., • Take the initiative to investigate and propose new method, process, technique, tool, component, or technology improvements for quality, timeliness, and efficiency., • Conduct in-depth technical interviews and make hiring recommendations for capable and talented technical staff to grow an effective Engineering team. This job description is not designed to cover or contain a comprehensive listing of activities, duties or responsibilities that are required of the employee. This job description indicates, in general the nature and levels of work, knowledge, skills, abilities and other essential functions (as covered under the ADA) expected of the incumbent. Duties, responsibilities and activities may change at any time with or without notice as required. Power Device Corporation is an Affirmative Action/Equal Opportunity Employer and is committed to providing equal employment opportunity (EEO) for all persons in all facets of employment. All qualified applicants will receive consideration for employment without regard to race, color, religion, age, gender, sexual orientation, gender identity, national origin, citizenship status, marital status, genetic information, disability, protected veteran status or any other legally protected status.

Job Description FLSA STATUS: Salary/Exempt DEPARTMENT: Research and Development SUPERVISOR: Engineering Manager DIRECT REPORTS: No Position Summary Power Connector, LLC is entering a new and exciting phase of growth and opportunity filled with innovative and progressive thinking and strategizing. In December 2021, Power Connector was acquired by the Trexon Global network. With this historic transition comes the need to enhance and grow the company through restructuring, reorganization, modernization, optimization, and business development. We, at Power Connector, are responsible for revolutionizing the company and securing and expanding its global connection. Power Connector's Design Engineer is critical in contributing to the fundamental changes that are transforming Power Connector. This position is instrumental in enhancing and strengthening our design capabilities to enable the growth and development of the business by driving innovation and improvements via New Product Introduction and connector design iterations and enhancements. This position's primary focus is to contribute and execute on the team's strategic plans for design innovation and product line sustainability and expansion. Power Connector's Design Engineer is a dynamic, adaptable, open-minded problem solver with exceptional technical and analytical skills. This position plays a key role in sustaining and enhancing our current capabilities and output through strategic planning and engineering to increase efficiency and productivity in all design engineering disciplines. This position enjoys the inherent challenges of sustaining and growing a business by optimizing engineering processes and introducing new approaches to design in a diverse and dynamic organization. This position has a strong influence on the fundamental principles guiding design structure and functionality and works closely with the General Manager to realize the company's true designing potential. Minimum Qualifications Education: • Bachelor's of Science in engineering or related field Experience: • 3-5 years of experience of design engineering or related field, • 2-5 years of electrical connector design experience Knowledge: • Ability to create 3D Computer-aided design (CAD) models and drawings, • Ability to read drawings, specifications, test procedures, etc., • Fundamental mathematical and physical principles, • Proficient in MS Office, • Geometric Dimensioning and Tolerancing (GD&T) Skills: • Good oral and written communication and presentation skills, • Great interpersonal skills, • Excellent organizational skills, • Results-oriented with strong analytical skills, • Ability to work well independently and part of a team, • Ability to motivate team members in a creative and effective manner, • Ability to work effectively under stressful and dynamic environments Job Responsibilities • Assist with research and development, new product introduction, and production deployment., • Create CAD models, drawings, specification sheets, and prototypes for new and existing products utilizing Solidworks., • Modify existing products to improve efficiency and performance., • Design for manufacturability., • Research materials and production costs to determine manufacturing requirements., • Ensure product designs conform to customer and government specifications., • Test designs to ensure they meet safety, usability, and environmental impact standards., • Analyze data from tests and identify opportunities for improvement., • Collaborate with engineering, sales, procurement, and production teams., • Present designs and prototypes to customers and colleagues., • Create BOMs and routings for new products, legacy products, and engineering changes as necessary., • Develop and manage costing analysis as necessary during product development and deployment., • Create part numbers, assign classification, build product structure and Bill of Materials, generate routings, assign standard labor times, etc. for all levels of components and assemblies in current MRP system., • Manage and participate in product design reviews to provide input on design and manufacturing requirements, functional requirements, capacity, potential failure modes, etc., • Manage projects, including budgets, schedules, and costs when applicable., • Perform DFMEAs, PFMEAs, and Risk Assessments., • Ensure that the company's designs and designing processes comply with all government laws and regulations., • Review and calculate labor, material, and other production costs along with reviewing schedules and future production requirements to assist management in decision making., • Collaborate with quality team to assure products are being produced to applicable specifications., • Evaluate quality control processes and make recommendations for improvements in quality control., • Devise procedures to inspect and report quality issues., • Assure the reliability and consistency of product manufacturing by checking processes and final output., • Facilitate proactive solutions by collecting and analyzing manufacturing data., • Document and optimize design procedures to ensure replicability and compliance with internal and external standards., • Contribute to internally driven and customer-driven Root Cause Corrective Actions and failure analysis., • Assist in the preparation for quality audits., • Any additional tasks necessary to execute on the team's strategy for design sustainability, improvement, and optimization. Other responsibilities, initiatives and ad-hoc projects as required. Physical Requirements The physical demands described here are representative of those that must be met to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is regularly required to sit for prolonged periods of time, working at a computer, stand, bend, twist, and lift up to 25 lbs. The noise level in the work environment is usually low to moderate.

Job DescriptionDescription: At Maxxima, we design and develop innovative LED lighting, electrical, and safety solutions for automotive, heavy-duty truck, and consumer applications. We are seeking an Electrical Engineer with a hardware-focused background to support product development, electrical lab testing, circuit troubleshooting, and PCB validation for our growing product lines. This is a hands-on engineering role working onsite at our Hauppauge, NY location, centered on electrical hardware testing, circuit-level debugging, and product validation. You’ll work closely with engineering leadership and cross-functional teams throughout the full product lifecycle, from prototype and testing through manufacturing and production support, while helping us continue building innovative products and a brand we’re proud of. Why Join Maxxima?: • Hands-on electrical engineering role focused on hardware, testing, and product validation, • Exposure to full product development lifecycle in LED lighting and automotive electrical systems, • Collaborative, fast-moving engineering team with direct access to leadership Benefits & Perks: • 401(k) with generous company match, • Paid time off, company-paid holidays, and volunteer day, • Highly subsidized medical coverage, plus dental and vision options, • Company-paid life insurance and disability coverage, • Healthcare concierge services and Employee Assistance Program (EAP), • Employee discounts on Maxxima products, entertainment, travel, and more Key Responsibilities: • Support product development from prototype to production, focusing on hardware validation and circuit performance, • Perform electrical lab testing, troubleshooting, and failure analysis on product designs, • Conduct PCB bring-up, board-level debugging, and verification testing, • Analyze analog and digital circuit behavior to ensure performance, safety, and reliability, • Use lab equipment such as oscilloscopes, multimeters, power supplies, and signal generators, • Review and interpret schematics, PCB layouts, wiring diagrams, and technical specifications, • Develop and improve test procedures and validation methods for electrical products, • Document test results, findings, and corrective actions for engineering and quality teams, • Collaborate with engineering, manufacturing, and quality teams to resolve hardware issues during development Requirements: • Bachelor’s degree in Electrical Engineering or related field, • 2+ years of experience in electrical engineering, product testing, or hardware validation, • Strong understanding of analog and digital circuitry, • Hands-on experience with PCB debugging, schematics, and electrical troubleshooting, • Experience using standard electrical lab equipment, • Strong analytical, troubleshooting, and communication skills, • Ability to manage multiple projects and priorities, • Experience with LED lighting, automotive electronics, or power electronics a plus, • Exposure to embedded systems (hardware interaction only) a plus, • Basic scripting (C, C++, Python, or LabVIEW) for test support a plus Salary Range: $65,000 - $75,000 Maxxima is a division of Panor Corp. We are an equal opportunity employer. Panor Corp. provides equal employment opportunity to all employees and applicants without regard to actual or perceived race, creed, color, citizenship, sex, pregnancy, religion, national origin, military status, marital status, sexual orientation, gender expression or identity, genetic information (including genetic predisposition), age, disability, status as a victim of domestic violence, or any other group protected by applicable federal, state and local laws. This policy applies to all terms and conditions of employment including, but not limited to, recruitment, hiring, assignment of duties, benefits, promotion, discipline, harassment, training, compensation, leave of absence, layoff and termination. Requirements:

Job DescriptionDescription: We are seeking a hands-on Automation & Controls Engineer to support, troubleshoot, and improve a wide range of manufacturing equipment in a regulated pharmaceutical environment. This role is ideal for mechanically inclined problem-solvers who enjoy being on the production floor, working directly with machines, controls, and electrical systems – not behind a desk. Job Type: Full-Time Location: Hauppauge, NY Works Hours: Monday – Friday, 8:00AM – 4:00PM Pay Range: $90,000 - $140,000 per year, depending on experience Start Date: ASAP What makes this role exciting: • A true automation playground – work hands-on with a wide variety of manufacturing equipment, controls platforms, and technologies in a complex pharmaceutical environment., • Real impact, real machines – you’ll diagnose, fix, and improve equipment that directly supports production, quality, and reliability – not abstract or purely digital systems., • High visibility & ownership – your expertise will be relied on across maintenance, engineering, and operations, with meaningful input into equipment improvements and upgrades., • Constant learning & challenge – no two days look the same; you’ll be exposed to diverse machinery, evolving technology, and new technical challenges., • Hands-on engineering – ideal for mechanically curious problem-solvers who prefer being on the floor, working with equipment, over desk-only work. Why Join CPC? At CPC, you’ll be part of a team that has set the standard in pharmaceutical development and contract manufacturing since 1971, helping bring high-quality OTC, dietary supplement, and prescription products to market faster and safer than ever. We pride ourselves on quality as a core value, innovative problem-solving, and a collaborative culture where everyone plays a role in advancing formulation and manufacturing excellence. CPC offers an inclusive, respectful workplace with opportunities to grow your skills and career while working with cutting-edge technologies and serving leading global brands. With a commitment to employee success, competitive benefits, and a culture built on teamwork and integrity, CPC is a place where your contributions truly make an impact. Requirements: Responsibilities: In this role, you will: • Troubleshoot and resolve PLC, electrical, and control system issues across a wide range of manufacturing equipment to minimize downtime and improve reliability., • Design, implement, and optimize machine control systems, including PLCs, HMIs, servos, and electrical components., • Own automation documentation and standards, maintaining current PLC/HMI programs, electrical drawings, and equipment documentation., • Collaborate closely with maintenance, engineering, and operations teams to execute repairs, improvements, change control, and equipment qualification., • Mentor and guide mechanics and technicians, promoting safe work practices, strong troubleshooting skills, and first-time-right execution. Education & Experience: • Bachelor’s Degree in Electrical Engineering, Automation Engineering, or a related engineering discipline., • Minimum 3 years of progressive experience supporting and improving automated manufacturing equipment. Skills, Knowledge & Abilities: • Mechanically curious and systems-oriented thinker, • Comfortable working directly on equipment in a production environment, • Enjoys variety, challenge, and continuous learning, • Practical, hands-on problem solver – not purely theoretical, • Hands-on experience with PLC, HMI, and servo systems (Allen-Bradley, Siemens, Mitsubishi), • Experience troubleshooting electrical control panels, sensors, drives, and actuators, • AutoCAD or similar electrical drafting experience preferred, • Working knowledge of OSHA and NEC requirements

Job Description Firmware Engineer Key Responsibilities: • Firmware Development: Design, develop, and maintain embedded firmware for power supply products, including microcontroller programming, device drivers, and communication protocols. Familiarity with Microchip, TI and Freescale uP’s and their coding., • Algorithm Development: Collaborate with hardware engineers to develop and optimize control algorithms for power conversion, voltage regulation, and protection mechanisms., • Integration and Testing: Integrate firmware with hardware platforms and conduct thorough testing to ensure functionality, reliability, and compliance with specifications and standards., • Documentation: Prepare clear and comprehensive documentation including design specifications, test plans, and user manuals to support product development and customer support activities., • Troubleshooting and Debugging: Identify and resolve firmware-related issues through systematic debugging, testing, and analysis of system behavior., • Continuous Improvement: Stay abreast of emerging technologies, industry trends, and best practices in firmware development to propose and implement continuous improvements in our products and processes., • Collaboration: Work collaboratively with cross-functional teams to ensure alignment of firmware development efforts with overall project goals and timelines. Qualifications: • BS in EE or Computer Science or related fields, • Prefer 3-5 years experience but entry level / new graduate will be considered based on experience., • Domestic and international travel may be required., • Bilingual Mandarin a plus., • Assembly language knowledge a plus., • Sponsorship for H1B is available., • Onsite position in NY(Long Island) office, no hybrid or remote option Benefits: • 401(k), • 401(k) matching, • Dental insurance, • Health insurance, • Vision insurance, • Life Insurance, • Paid time off Location – New York (Long Island)

Job Description iRocket is pushing the frontier of reusable rocket propulsion. We’re looking for a Turbo Pump Engineer to design, analyze, and test turbomachinery for our reusable engines. The Role • Design, model, build, and test high-performance turbopumps (inducers/impellers/diffusers) for cryogenic rocket engines., • Perform hydrodynamic, aerodynamic, bearing, and rotor-dynamics analysis for rotating assemblies., • Develop manufacturing plans and build books, manage tolerance stack-ups, and ensure as-built compliance., • Monitor performance trends, analyze cavitation, vibration, thrust-balance, and clearance growth., • Execute root-cause investigations, iterate designs to improve cost, lead-time, and reliability., • Work cross-functionally with manufacturing, test, and propulsion design teams. Requirements • Bachelor’s degree in Mechanical or Aerospace Engineering., • 3+ years of turbomachinery or rocket-engine component experience, including design/build/test of turbopumps or related systems., • Strong knowledge of fluid/rotordynamics, cryogenics, bearings, and rotating machine behavior., • Proficiency in CAD (Siemens NX, SolidWorks, etc.), CFD/FEA, and test instrumentation., • Experience with machined, additively-manufactured parts, weldments, fasteners, seals, and rotating assemblies., • Strong communication and documentation skills, and ability to lead hardware workflows to delivery. Benefits • Health Care Plan (Medical, Dental & Vision), • Retirement Plan (401k, IRA), • Life Insurance (Basic, Voluntary & AD&D), • Paid Time Off (Vacation, Sick & Public Holidays), • Family Leave (Maternity, Paternity), • Short Term & Long Term Disability, • Wellness Resources

SOFTWARE ENGINEER ClearVision Optical is seeking a skilled Software Engineer with a passion for designing and building high-performance, scalable applications that aid in problem solving. The Software Engineer should have proven skills in data-driven application development and motivated to advance business decision-making. The successful candidate will have experience in application development, strong cross-platform development skills and a background which includes full stack development. This role will involve participation in the full development cycle including design of software, developing code, updating technical documents, generating test plans, ensuring code meets requirements through unit testing, and resolving discrepancy reports. This individual will work with our high performing, fun-loving, game-playing Technology team. The right individual enjoys having fun at work and has a great respect for learning opportunities. The right person will enjoy being playful, love “geeking out” and will be attracted to learning from our intelligent team members. The Software Engineer will partner across our organization to solve important business challenges and help drive the development of cutting-edge technologies to further our business needs. Working directly with our sales team daily, the Software Engineer will create and enhance tools that enhances their revenue generating potential. With direct access to our leaders, the Software Engineer will determine the development strategy, define deliverables, set priorities based on business benefit, manage projects and document requirements for customer-facing websites, app development, manufacturing technologies and more. The development platform will leverage variable data sources from across the organization and ERP system. If you have strong communication skills, functional expertise, an analytic nature, and a keen attention to detail this may be the right opportunity for you. We are committed to growing ClearVision with dynamic and motivated talent who will be passionate about our learning environment, and dedication to our process improvement and automation efforts. We offer a challenging and cohesive team environment! Our benefits are comprehensive, and we pride ourselves on providing countless learning opportunities. We are a values-based organization that takes pride in our fun culture and invests in developing our talent. In fact, our culture is award-winning, as we have been named a Best Company to Work for in NY for 11 years. If you are looking to join a winning team, this may be the right opportunity for you. RESPONSIBILITIES INCLUDE: • Ensure data integrity and quality in production environments, • Work closely with the management and executive teams to design faster, more user-centric, and efficient applications. Propose innovative technical solutions to business problems on a proactive basis, • Develop and enhance modern cross-platform desktop, web, and mobile applications using Flutter and Dart, • Develop and maintain back-end systems and APIs using Rust, Python, and PostgreSQL, • Apply DevOps discipline across the development lifecycle, including CI/CD pipelines, automated testing, infrastructure-as-code, and reliable deployments, • Manage and maintain AWS cloud infrastructure and environments to ensure security, reliability, and scalability, • Incorporate AI and machine-learning capabilities into our products and internal tools where they deliver genuine business value, • Develop software prototypes of the proposed solutions, • Write modern, clean, and maintainable code for multiple platforms, • Provide baseline performance and scale assessments of applications, • Follow development standards and procedures while developing applications, • Work with QA to verify application functionality and address defects POSITION REQUIREMENTS: • Bachelor’s degree in computer science, Computer Engineering, or a similar field required; advanced degree preferred, • The ideal candidate will possess a minimum of 3 years of experience in mixed development environments with an emphasis on data driven application models, • Hands-on experience with our stack — Flutter/Dart, Rust, and Python — with particular emphasis on PostgreSQL, • Experience managing and maintaining cloud infrastructure on AWS, along with DevOps practices such as CI/CD, automated testing, and infrastructure-as-code, • Leverages AI-assisted development tools to work more productively while retaining full ownership of the code — able to critically evaluate, understand, maintain, and stand behind everything that ships, • Understanding of database design practices, including database normalization concepts, • Proficient at performance monitoring, • Willing to expand their knowledge and practical use of tips and techniques to ensure performance, scalability, high availability, quality, and accessibility of our database systems and data., • Knowledge of network administration, infrastructure, and support is a plus

Summary:A Test Engineer I - Software develops test systems and software to ensure the quality and reliability of our products. North Atlantic Industries offers comprehensive and competitive packages including:Benefits:Medical, Dental, and Vision InsuranceCompany-provided Life and AD&D InsuranceVolun

Job Description iRocket is engineering fully reusable, fully autonomous small launch vehicles to enable responsive, cost-effective, and sustainable access to space. Our team is building the infrastructure—both in orbit and on the ground—needed to support frequent launches and mission operations. The Role: We are seeking a Construction Project Engineer to lead and support the development of iRocket’s factory, test, and facility infrastructure. This role will play a key role enabling our production and test operations by implementing facility projects, collaborating with contractors, and coordinating with internal stakeholders. • Support all aspects of project implementation from planning through execution, • Create scopes of work, obtain competitive bids, and oversee contractor selection, • Conduct job walk-downs and interface with vendors, engineers, and internal teams, • Review technical plans, drawings, and specifications to ensure alignment with project goals, • Monitor project schedule, budget, and deliverables, • Respond to scope, schedule, or deliverable questions from stakeholders, • Manage and maintain all project documentation (RFIs, submittals, change orders, etc.), • Participate in meetings and presentations with senior leadership as needed Requirements • Bachelor’s degree in Engineering, Construction Management, Architecture, or related field, • Ability to read and interpret technical drawings, plans, and specifications, • Experience in facilities, infrastructure, or industrial construction in aerospace or high-reliability sectors, • Strong computer and software skills (project scheduling, documentation, collaboration tools), • Excellent verbal and written communication skills with internal teams, vendors, and contractors, • Aptitude for problem-solving, balancing scope, cost, and schedule Benefits • Health Care Plan (Medical, Dental & Vision), • Retirement Plan (401k, IRA), • Life Insurance (Basic, Voluntary & AD&D), • Paid Time Off (Vacation, Sick & Public Holidays), • Family Leave (Maternity, Paternity), • Short Term & Long Term Disability, • Wellness Resources

Job Description Job Title: Coordinator, Quality FLSA: Non-Exempt Reports To: Quality Department Management Position Summary: The Quality Coordinator plays a key role in supporting quality assurance activities and projects as directed by the Quality Assurance Manager. This position involves analyzing and investigating to enhance products, processes, and data integrity while ensuring compliance with quality and regulatory standards. Daily responsibilities: • Assist with all quality-related activities and projects as directed by the Quality Assurance Manager., • Analyze and investigate to improve product quality and processes., • Respond to customer inquiries regarding product specifications and the quality management system., • Ensure products meet established quality and regulatory standards, including reliability, usability, performance, and safety., • Collaborate with teams and committees to maintain organizational quality standards., • Maintain accurate and up-to-date information in the ERP system., • Collect and organize material and product documentation to support regulatory requirements., • Review customer specifications for accuracy., • Create, revise, and release product drawings as needed., • Assist in coordinating and releasing product Change Notifications., • Communicate with management to address and resolve issues., • Recommend and implement improvements to operational methods and practices., • Investigate customer complaints and non-conformance issues, responding to requests for information as necessary., • Participate in corrective and preventive actions, including root cause analysis., • Conduct internal audits of management systems per the audit schedule., • Support external audits conducted by customers and regulatory bodies., • Take on additional tasks and projects as assigned by the Quality Assurance Manager., • Travel: Less than 5%. Education/Technical Certifications: • An Associate degree or equivalent work experience is preferred, but candidates with diverse educational and professional backgrounds are encouraged to apply., • Relevant certifications (e.g., Quality Auditor, Quality Engineer, Quality Improvement Associate, Lean Six Sigma Green Belt) are a plus. Experience: • Proven experience in a Quality Assurance or Quality Control department., • Familiarity with quality management systems and their tools and methods., • Knowledge of standards such as ISO 13485, ISO 9001, and 21 CFR Parts 820, 210, and 211 is a plus. Skillsets: • Understanding medical devices, biotechnology, and cleanroom environments is beneficial., • Proficient in Microsoft Office, particularly MS Excel., • Knowledge of manufacturing and validation processes, as well as distribution and environmental systems, is advantageous., • Strong communication skills for effective collaboration., • Excellent data collection and analysis abilities., • High attention to detail and ability to multitask efficiently