Trabajos welder en Missouri

Job Description For almost 30 years, SQA Services has been a premier leader in the provision of managed supplier quality services for audits, assessments, remote surveillance assessments, corrective actions, remediation, inspections, and engineering to manufacturers within all industries. We deliver services by deploying associates who are located throughout the United States and in 90+ countries around the world to your supplier sites. Our associates are expert quality assurance professionals with broad experience and local knowledge who can represent our clients on-demand and on-site faster than our competitors. We are seeking a detail-oriented Welding Inspector to ensure the quality, compliance, and integrity of welded components and assemblies. This role is responsible for performing inspections, verifying documentation, and ensuring all materials and workmanship meet applicable standards, drawings, and specifications. This position with be on site 5 days a week, for 4-8 hours a day. This is a 3-6 month contract. Key Responsibilities: • Perform visual inspection (VT) of structural welds in accordance with AWS D1.1 acceptance criteria, • Evaluate weld workmanship and surface condition, • Identify weld discontinuities including:, • Cracks, • Undercut, • Porosity, • Overlap, • Incomplete fusion indications, • Arc strikes, • Excessive reinforcement, • Crater defects, • Verify weld profiles, weld size, and contour requirements, • Inspect fillet welds, groove welds, CJP and PJP welds Welding Documentation Review • Review and verify approved WPS documentation, • Confirm welder qualifications and continuity records, • Verify welding processes and consumables comply with approved procedures, • Review fabrication drawings and weld symbols, • Ensure inspection requirements are properly flowed down In-Process and Final Inspection • Perform pre-weld, in-process, and final inspections, • Verify fit-up, joint preparation, alignment, and cleanliness, • Monitor workmanship during fabrication activities, • Verify repairs and rework activities meet acceptance criteria, • Coordinate with NDE personnel when required Reporting and Documentation • Generate inspection reports and nonconformance documentation, • Document weld findings accurately and clearly, • Provide objective disposition recommendations, • Support corrective action and root cause investigations, • Maintain inspection records and traceability documentation Supplier / Source Inspection Support • Perform source inspections at supplier facilities when required, • Support supplier quality evaluations and audits, • Communicate technical concerns professionally with suppliers and customers, • Assist in process improvement and workmanship standardization activitiesRequired Qualifications: Education / Experience • High school diploma or equivalent required, • Technical training in welding inspection preferred, • Minimum 3–5 years of structural welding inspection experience preferred, • Experience inspecting structural steel fabrication and welded assemblies Technical Knowledge Strong working knowledge of: • AWS D1.1 requirements, • AWS B1.11 visual inspection practices, • Weld symbols and fabrication drawings, • Welding processes:, • FCAW, • GMAW, • SMAW, • GTAW (preferred), • Structural steel fabrication practices, • Weld gauges and inspection tools, • Weld discontinuities and workmanship evaluationPreferred Qualifications:, • Certified Welding Inspector (CWI), • VT Level II certification, • NDE certifications (MT/PT preferred), • OSHA safety training, • Structural steel fabrication experienceNote: This position requires access to ITAR-controlled technical data and/or defense articles. As such, the candidate must be a U.S. citizen or U.S. lawful permanent resident (green card holder) to comply with the International Traffic in Arms Regulations (ITAR). Applicants who do not meet these criteria will not be considered for this role. SQA Services is an Equal Opportunity Employer. Employment is based on merit and qualifications, and is not influenced by race, color, religion, gender, national origin, veteran status, disability, age, sexual orientation, gender identity, marital status, or any other legally protected status. #ZR We may use artificial intelligence (AI) tools to support parts of the hiring process, such as reviewing applications, analyzing resumes, or assessing responses and identifying potential inconsistencies or verification signals in application materials based on available information. These tools assist our recruitment team but do not replace human judgment. Final hiring decisions are ultimately made by humans. If you would like more information about how your data is processed, please contact us.

Job Description The Fabricator builds and supports fabrication and assembly work for hydraulic power units and related components, using shop equipment to cut, form, weld, and finish metal and tubing. This role is accountable for completing work safely, meeting specifications, and supporting on-time delivery through accurate workmanship, documentation, and coordination with the fabrication team. Compensation: $26 hourly Responsibilities: Supervisory Responsibilities: This position has no supervisory responsibility. Duties/Responsibilities: Fabricate and assemble hydraulic power units, frames, and related components to drawings, work instructions, and specifications. Set up and operate fabrication equipment and hand tools, such as drill press, band saw/cutoff saw, plasma cutter, MIG welder, and grinders, to cut, drill, grind, and fit materials. Assemble and kit fluid power systems and subassemblies to support production flow and on-time completion. Bend hydraulic tubing and fabricate hydraulic hoses to specification; verify orientation, lengths, and required fittings prior to release. Read and interpret hydraulic/pneumatic and basic electrical schematics, drawings, and bills of material to complete builds correctly. Perform in-process checks and operate test stands and test equipment as assigned to verify product functionality and conformance. Prepare completed components for paint or finish, packaging, and shipment; complete required documentation accurately and on time. Handle, label, and dispose of waste materials properly in accordance with department requirements. Support department priorities and assist other team members as directed by supervision. Work safely at all times by following required PPE, safe work practices, and equipment operating procedures; stop and escalate unsafe conditions immediately. Participate in training and continuous improvement activities to improve safety, quality, and production efficiency. Perform basic preventative maintenance and care of equipment, such as cleaning and lubrication, and report equipment issues that could impact safety or quality. Operate material handling and shop equipment needed to perform assigned work. Inspect workmanship and verify critical characteristics; report defects, damaged materials, or questionable conditions before proceeding. Support ISO 9001:2015 requirements as defined in Hyspeco quality procedures and processes, including documentation and control of nonconforming output. Qualifications: Required Skills/Abilities: Mechanical and fabrication aptitude, including welding, cutting, grinding, drilling, and measuring. Ability to read prints and schematics, including hydraulic, pneumatic, and basic electrical diagrams. Strong quality focus and attention to detail. Time management skills and the ability to meet schedule commitments. Knowledge of safe work practices and strong housekeeping or 5S habits. Ability to learn and apply new processes, tooling, and work instructions. Ability to work effectively with minimal supervision after training and communicate status and issues promptly. Teamwork and collaboration across fabrication, production, and quality. Professionalism, dependability, and strong attendance. Education & Experience: High school diploma or GED and at least 1 year of fabrication, welding, assembly, or related manufacturing experience, or equivalent hands-on training required. Technical certificate or 2-year degree in welding, industrial technology, mechanics, or a related field preferred. Additional welding and fabrication experience; familiarity with hydraulic and electrical prints and symbols. About Company Hyspeco, Inc. is a full-line Fluid Power Distributor of motion and control components centered on hydraulic, pneumatic, electro-mechanical, and fluid connectors. Hyspeco Inc. is setting the standard for designing, manufacturing, applying, installing, and delivering fluid power products and engineering emergency and preventive maintenance field services. Our progress is driven by the family-built atmosphere and employee-owner mindset.

Job Description Essex Industries operates in St. Louis, Missouri; Huntington Beach, California; and Milford, Connecticut, serving local, national, and international customers across both military and commercial markets. The company specializes in manufacturing platform controls, aircraft components, liquid oxygen equipment, and emergency breathing systems. Essex is currently seeking a skilled Welder to join our team. In this role, you will perform horizontal and vertical welding on a wide range of metals and alloys, producing high-quality products designed to meet rigorous strength and pressure requirements. Essential Duties • Primary focus on TIG/MIG welding & finishing, • Perform under general supervision, a variety of tasks requiring a thorough knowledge of welding techniques, tools, machines and equipment., • Work from engineering drawings, blueprints, rough sketches and MI’s., • Inspect completed work for conformance to specifications., • Perform all work with adherence to safety procedures., • Complete all required documentation in a timely manner Required Education/Experience/Certifications: 1-3 years technical training and at least one year of experience working in welding position or equivalent of the two. Required Skills: • Language Ability: Ability to read and interpret instructions., • Math Ability: Ability to know measurements., • Blueprint reading: working knowledge of blueprints, • Reasoning Ability: Ability to solve practical problems and deal with a variety of variables in situations where only limited standardization exists. Ability to interpret a variety of instructions furnished in written or oral form., • Work Environment: Shop; Moderate noise level with welding fumes, airborne particles and vibration, • Working Conditions: Somewhat disagreeable working conditions. Exposed to any number of elements and with one continuously present to the extent of being objectionable, or with several elements present to the extent of being objectionable but usually not more than one at a time. Physical Demands: Moderate Physical Demand: Continuously lifting or moving light weight material; Continuously lifting or moving material of very light weight in difficult work positions; Frequently lifting or moving average weight material; Frequently lifting or moving Why Choose Essex? Since 1947, Essex has been offering high quality parts and services to our customers. Our employees are what makes that happen so we do our best to take care of what matters most, by offering a competitive total rewards package for our employees. It’s our commitment to making this a great place to work. Benefits • Base Pay and Overtime Pay Eligible, • Bonus Opportunity, • Paid time off, • 10 company holidays, • Training & Development, • Retirement Benefits – 401k matching, • Tax-Advantaged Accounts, • Medical, dental, vision coverage, • Flexible Spending Account, • Life Insurance, • Parental Leave, • Pet Insurance, • Employee Assistance Program

Job Description Servco Equipment Company (St. Louis, MO) is a local manufacturer specializing in custom commercial kitchen equipment and stainless-steel fabrication. We have an immediate opening for an experienced TIG Welder / Stainless Steel Fabricator to join our production team. If you’re confident welding thin-gauge stainless steel (12–20 gauge), can read fabrication prints, and take pride in clean, accurate work—this is a great fit. Pay $22.00 – $26.00 per hour (based on experience) Job Type Full-time Location St. Louis, MO 63139 (reliably commute or relocate before start) Key Responsibilities • Perform TIG welding on stainless steel components and assemblies (12–20 gauge)., • Select appropriate welding procedures and techniques to ensure proper penetration, fusion, strength, and alignment., • Read and interpret blueprints, fabrication prints, production orders, bills of material, and process sheets., • Fit-up parts using clamps and fixtures; maintain dimensional accuracy and alignment; spot weld/tack as required., • Weld and assemble parts into sub-assemblies or complete assemblies., • Inspect work for accuracy and quality prior to moving to the next step of manufacturing., • Support other shop areas as needed (flexible team environment). Qualifications • Ability to read and interpret complex drawings/blueprints., • Strong working knowledge of welding equipment, welding procedures, material characteristics, and basic metallurgy., • Proven TIG welding skill and familiarity with basic fabrication equipment/machines., • Ability to weld 12–20 gauge stainless steel with consistent quality., • Flexibility to work 1st shift, Saturdays, and overtime when needed. Requirements • High school diploma or equivalent, • 2+ years welding experience (required), • 2+ years TIG welding experience (required), • Stainless steel welding experience (preferred), • Trade school certification and additional (welder certification) knowledge is a plus Benefits • 401(k) + 401(k) matching, • Health insurance + Health Savings Account (HSA), • Dental and vision insurance, • Flexible Spending Account (FSA), • Life insurance, • Paid time off (PTO), • Retirement plan Schedule • Monday–Friday, • Day shift / 1st shift, • 8-hour shift, • Overtime available

Job Description Job Title: Quality Technician Location: St. Louis, MO Type: Direct Hire Work Model: Onsite – onsite Overview System One is seeking a Quality Technician (or Engineer) to support our client's structural steel fabrication facility in the St. Louis, MO area. Responsibilities • Interface with engineering, construction, management, clients, and inspectors on quality and welding concerns at project sites and/or shop., • Utilize quality programs including the American Institute of Steel Construction (AISC) to monitor project quality., • Implement quality assurance/quality control programs and review quality requirements from owners, manufacturers, and engineers., • Manage quality document submittals, including inspections, reports, and project-specific quality documents., • Support vendor surveillance activities and arrange third-party inspections such as bolting, welding, and nondestructive testing., • Develop and implement electronic welding procedures per AWS codes, including writing WPSs, PQRs, and welder certifications., • Certify welders according to AWS and CWB codes, maintaining their certifications and developing welder continuity programs., • Perform inspections/testing within expertise, including bolt testing of permanently installed bolts., • Interface with clients through surveys at project start, during, and at project completion., • Document inspections and quality control activities, and write weekly Toolbox Talks., • Manage the Non-Conformance Report (NCR) program and lead investigations., • Oversee calibration of equipment and perform weekly quality audits., • Assist with internal audits and maintain quality manuals, forms, and procedures., • Interact regularly with shop floor operations to ensure quality standards are maintained., • Travel across North America for meetings, site visits, and client interactions as needed., • Exhibit reliable attendance and support project and office obligations. Management Responsibilities • Manage and supervise NDE subcontractors and train employees in quality procedures. Requirements • Bachelor’s degree in Engineering, Construction Management, or related field and 3 years of field quality experience, or equivalent., • ASNT Level I certification preferred., • AWS Certified Welding Inspector preferred., • CWB Certified Welding Inspector/Supervisor preferred., • NACE Certified Coating Inspector Level I preferred., • USACE certifications preferred. System One, and its subsidiaries including Joulé and Mountain Ltd., are leaders in delivering outsourced services and workforce solutions across North America. We help clients get work done more efficiently and economically, without compromising quality. System One not only serves as a valued partner for our clients, but we offer eligible employees health and welfare benefits coverage options including medical, dental, vision, spending accounts, life insurance, voluntary plans, as well as participation in a 401(k) plan. System One is an Equal Opportunity Employer. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex (including pregnancy, childbirth, or related medical conditions), sexual orientation, gender identity, age, national origin, disability, family care or medical leave status, genetic information, veteran status, marital status, or any other characteristic protected by applicable federal, state, or local law. Ref: #369-Nuclear Fort Mill

Job Description We're SteelCon Inc., and we're hiring multiple full-time Structural Welders to join our team in St. Louis, MO! If you're comfortable working independently to complete accurate, safe, and high-quality welds, then you could be the right fit. Keep reading to learn more! HERE'S THE DEAL Pay: You'll earn $20.00 - $24.00/hour, based on experience. Schedule: Our Structural Welders usually work from 7:00 am to 4:00 pm, Monday through Friday. Overtime is available, and some weekends may be required to meet business needs. Benefits: • PTO, • Health insurance, • Dental, • Vision, • 401(k), • Company parties OUR STRUCTURAL WELDER IS RESPONSIBLE FOR: • Following blueprints to properly plan, lay out, and fit metal components (plate stiffeners, stiffened panels, bulkheads, and frames) while maintaining alignment tolerances, • Accurately locating and marking reference lines, • Using tools like jacks and turnbuckles to align parts, • Setting, fitting, and erecting structural assemblies and modules within alignment tolerances, • Installing structural foundations and outfit items (doors, hatches, brackets, etc.), • Tack welding panels, assemblies, and more, • Using machinery like ironworkers, presses, and plate rolls to roll, bend, flange, cut, and shape metal parts, • Accurately following instructions with minimal supervision, • Performing other duties as assigned LEARN A LITTLE ABOUT US At SteelCon Inc., we don't just fabricate steel - we build the backbone of America's progress. Our mission is to deliver cutting‑edge structural solutions with unmatched reliability. We live by our core values: Excellence, Responsibility, Innovation, and Teamwork. These values shape our culture, guide our decisions, and create an environment where employees thrive. When you join SteelCon, you join a company committed to your long‑term success through advancement opportunities, career development, and a workplace where your contributions truly matter. QUALIFICATIONS Our Structural Welder must be able to: • Adequately operate a cutting torch, • Adjust the welder to ensure proper feed rate and temperature, • Properly operate forklifts, jib hoists, and overhead cranes, • Learn and use hand signals for crane operation, • Read, understand, and follow cutting lists, shop orders, and shop drawings, • Perform general math calculations (addition, subtraction, multiplication, division, fractions, decimals, etc.), • Read, write, and follow semi-complicated verbal and written instructions, • Communicate with managers and co-workers, • Set priorities, meet goals, and work under periodic supervision, • Use a tape measure/ruler, • Follow safety policies and take accountability for your work, • Multitask Required Abilities: • Maintain American Welding Society certification on a 1-inch plate in flat position using the gas metal arc welding and flux-cored arc welding processes, • Pass the fillet weld break test using the gas metal arc welding process, • Pass a basic welding test that covers shop drawing interpretation, weld symbols, welding processes, weld process symbol interpretation/application, and a visual acuity test, • Pass a fitting test that covers shop drawing interpretation, fractional number calculations, basic geometry, etc. Do you have what it takes? Apply now with our initial application!

Job Description Join a growing manufacturing organization serving customers across a variety of industries. Located in Millstadt, Illinois, within the greater St. Louis metropolitan area, MAC Medical offers an opportunity to build your career with a local manufacturer while being part of a growing organization. MAC Medical is known for having a team culture that works together and inspires us to be better! We are a family owned and operated business founded in 1998 which builds American made medical equipment. In 2020, our growing business started Copperworks Industries, a plastic laminate cabinet company. Join our team and grow with us! JOB SUMMARY TIG Welder will be responsible for welding, cutting, and brazing metal pieces and products by using flame-cutting and hand welding equipment. ESSENTIAL FUNCTIONS • Perform TIG welding on stainless steel, • Fabricate and assemble medical equipment components to specification, • Grind, polish, and finish welds to cosmetic and sanitary standards, • Inspect completed welds for accuracy, penetration, and quality, • Operate fabrication equipment including grinders, saws, and hand tools, • Plans details of work order procedures; gathers required tools and materials based on instructions and specifications provided for the job., • Maintains, organizes, and cleans equipment and the work area., • Follow OSHA, company safety, and quality procedures, • Notifies supervisor when faulty equipment or defective materials are discovered., • Performs other related duties as assigned. REQUIRED SKILLS AND KNOWLEDGE • Basic understanding of design techniques, principles, and tools necessary for the precise production of technical plans, drawings, models, and blueprints, • Basic understanding of mathematics as related to welding assignments, • Knowledge of welding symbols and fabrication techniques, • Ability to lift up to 50 pounds and stand for extended periods, • Strong attention to detail dn workmanship, • Must pass Skill Assessment for Tape Measure and Welding Test EDUCATION AND QUALIFICATIONS • High school diploma or GED required, • Welding Certificate, or 2-5 years TIG experience, • Experience in medical, food-grade, pharmaceutical, or clean-finish welding environments preferred

Job DescriptionMust be willing to travel/temporarily relocate to Portland, OR. Why Skilled Trades Professionals Choose AAA USA: • Competitive Pay., • Overtime Opportunities., • Long-Term Assignments., • Multiple U.S. Locations., • Relocation Assistance Available., • Referral Programs., • Medical, Dental & Vision Benefits., • 401(k) with Company Match., • Paid Time Off & Paid Holidays. Position Summary:AAA United States, Inc. has partnered with a company in Portland, Oregon that is the premiere West Coast shipyard for building large Jones Act compliant articulated tug barges, deck barges, dump scows, oil spill recovery vessels, crane barges hopper barges and more. Essential Functions: • Tack and fit steel components together in preparation for final welding., • Set up and operate welding equipment safely and efficiently., • Perform production welding on heavy steel components., • Perform assembly and disassembly of steel components, • Weld and fit in flat, horizontal, vertical, and overhead positions., • Read blueprints and execute precise layout and fitting work., • Inspect completed welds to ensure top-quality workmanship and specification compliance., • Remove slag and finish welds with attention to detail., • Troubleshoot minor welding equipment issues as needed., • Work safely and follow all company safety standards and procedures., • Collaborate with a hardworking team committed to quality and continuous improvement. Requirements: • Ability to weld structural steel and become certified using 1/16” flux core wire in all positions on unlimited thickness plate., • Ability to pass weld tests including:, • Fillet welds on 1" plate (2G, 3G, and 4G)., • Groove welds on 1" plate (2G, 3G, and 4G)., • Strong math and measurement skills, including fractions and tape measure reading., • Ability to operate a hand-cutting torch efficiently and produce quality cuts., • Blueprint reading and steel layout experience., • Ability to follow written and verbal instructions., • AWS D1.1 / D1.5, • Strong safety mindset and commitment to safe work practices., • Ability to work independently and as part of a team., • Desire to learn, improve, and build new skills continuously.

Job Description D7 Pneumatics LLC is seeking an experienced QA/QC Manager to support our fabrication shop and field operations based in Jonesboro, Arkansas. This position will begin on a part-time or as-needed basis, with the potential to develop into a full-time role based on workload and company growth. The QA/QC Manager will be responsible for implementing and maintaining D7’s Quality Control Program, supporting ASME and National Board Code work, and ensuring fabrication and field activities comply with approved procedures, project specifications and applicable codes. Key Responsibilities Administer and enforce the D7 Quality Control Manual and related procedures. Oversee quality activities for shop fabrication and field installations. Review contracts, drawings, specifications and project requirements before work begins. Confirm the applicable codes, standards, inspection requirements and testing procedures for each project. Maintain compliance with applicable ASME, National Board and pressure-piping requirements. Coordinate with Authorized Inspectors, client representatives, engineers and third-party inspection agencies. Verify that approved Welding Procedure Specifications are available and properly followed. Review and maintain WPS, PQR and Welder Performance Qualification records. Monitor welder qualifications and continuity. Verify material receiving, identification, storage and traceability. Review Material Test Reports and certificates of compliance. Maintain weld maps, weld logs, inspection reports and project turnover documentation. Establish and monitor inspection hold points. Perform or coordinate fit-up, visual welding and final inspections. Coordinate nondestructive examination, including RT, UT, MT and PT, when required. Ensure pressure testing is performed using approved procedures, calibrated equipment and proper safety controls. Monitor preheat, interpass temperature and postweld heat treatment when applicable. Manage nonconformance reports, corrective actions and weld-repair documentation. Maintain calibration records for inspection and testing equipment. Control Code stamps, data reports and quality records as assigned. Assist with ASME, National Board, Authorized Inspection Agency and client audits. Conduct internal quality audits and recommend improvements. Prepare complete and organized project turnover packages. Train supervisors, welders, fitters and shop personnel on applicable quality requirements. Maintain a professional, practical and safety-focused quality culture. Required Qualifications Previous QA/QC experience in industrial fabrication, pressure piping, power-generation, boiler or pressure-vessel work. Working knowledge of welding inspection and fabrication quality-control methods. Ability to read fabrication drawings, piping isometrics, P&IDs, weld maps and technical specifications. Knowledge of welding procedures, welder qualifications and material traceability. Experience administering inspection, examination and pressure-testing requirements. Strong documentation, organization and communication skills. Ability to work independently and coordinate effectively with project managers, supervisors, inspectors and clients. Proficiency with Microsoft Word, Excel, email and electronic recordkeeping. Willingness to support both Jonesboro shop operations and field projects as required. Preferred Qualifications Knowledge of ASME BPVC Sections I, II, V, VIII and IX. Knowledge of ASME B31.1 Power Piping and ASME B31.3 Process Piping. Experience with National Board Inspection Code repair and alteration requirements. Experience working under ASME U and S Certificates and a National Board R Certificate. AWS Certified Welding Inspector certification. ASNT or employer-based NDE qualifications. Experience dealing with Authorized Inspectors and jurisdictional authorities. Experience in power plants, pulp and paper facilities, steel mills, sawmills or other heavy-industrial facilities. Employment Structure This position is intended to begin as part-time or as-needed employment. Hours may increase based on active projects, shop workload and field requirements. The position has the potential to transition into a full-time QA/QC management role as D7’s Code fabrication and pressure-piping operations expand s.

Job Description CORPORATE OVERVIEW Headquartered in St. Louis, Missouri with more than 1,200 employees and nearing $2B in revenue, Alberici is a diversified construction company that partners with leading organizations throughout North America to build their most challenging and important projects. Since our founding in 1918, Alberici earned a reputation for executing with quality, safety and trust. Combined with our 100+ years of experience, we provide construction solutions to the automotive, commercial, civil, energy, food & beverage, healthcare, heavy industrial, industrial process, and water industries. We build the critical structures that improve lives and strengthen communities. Our mission is simple — and our approach to delivering on it is equally straightforward. We are as open and honest with our employees and partners as we are with our clients. We are here to work together to do the best work possible to bring this mission to life. When it comes to our team, Alberici employees are built differently. We seek the best and brightest and are committed to investing in our people and providing the training and resources they need to learn, grow, and advance. Our Values: • Working Safely, • Valuing Diversity, • Serving Humbly, • Executing with Integrity, • Solving Creatively, • Engaging Fully What We Offer: • Profit-sharing plan, cash bonus programs and annual cost-of-living adjustments, • Generous salary increases and per diems for qualified out-of-town assignments, • Health, dental and vision insurance eligibility on day one, • Paid parental leave, • Continuing education reimbursement, • Personalized career development and training programs, • Minimum of 29 days of PTO (including holidays) for entry-level roles, • Fitness center for St. Louis office-based team members, • Gym membership reimbursement for project-based team members, • Corporate office cafeteria access, • Employee Resource Group (ERG) opportunities, • Philanthropy opportunities POSITION SUMMARY The Quality Technician interfaces with engineering, construction, management, clients and clients’ inspectors on quality and welding related concerns at project sites and/or Hillsdale Fabricators Shop. The Quality Technician also utilizes Alberici’s Quality Programs which includes the American Institute of Steel Construction (AISC), and other related programs as necessary to monitor the quality of projects. Essential Responsibilities & Duties include the following; however, other duties may be assigned. The Company provides reasonable accommodations to qualified individuals with a disability, unless doing so poses an undue hardship on the Company. To be a qualified individual, an employee must be able to perform each of the essential functions of his or her job with or without a reasonable accommodation. • Implements quality assurance/quality control programs for the Company., • Reviews owner, manufacturer and engineering quality requirements and applies them to the project., • Manages Quality Document submittals for projects, including subcontractors., • Manages project specific quality documents (dimensional checks, inspection reports and other various quality related documents)., • Supports planning, development and implementation of vendor surveillance activities for procured items., • Arranges for third party inspection service for bolting, welding, nondestructive testing, and others as may be required. Interfaces with third party inspection services per client inspection requirements., • Develops and implements electronic welding procedures for the Company (various AWS Codes), including writing WPSs, PQRs, and Welder Certifications., • Certifies welders per AWS (American Welding Society) and CWB (Canadian Welding Bureau) Codes and maintains their certifications according to same Code., • Develops and maintains a welder continuity program for both AWS and CWB., • Performs inspections/testing within field of expertise, including bolt testing of permanently installed bolts., • Interfaces with clients through client surveys at the start, during and at the end of projects., • Documents inspections and related quality control activities., • Writes weekly Quality Toolbox Talks., • Manages the Non-Conformance Report (NCR) Program, including writing NCRs and leading investigations., • Manages calibration of equipment., • Performs weekly Quality Audits., • Assists with the Annual AISC internal audit., • Assists with maintaining the Quality Manual, Quality Forms and Quality Procedures., • Interacts with the shop floor on a regular basis while continuously monitoring quality., • Travels to Company and subsidiary offices; offsite client, subcontractor, and supplier meetings; and other locations across North America to fulfill the essential duties of the role as required., • Exhibits regular and reliable attendance in person as required by the Supervisor, Company guidelines, and/or project and office obligations. Management Responsibilities • Manages and directs NDE Subcontractors., • Supervises in accordance with the organization's policies and applicable laws. Responsibilities include training employees. Education and Experience Bachelor’s degree in Engineering, Construction Management or related field and 3 years’ field quality experience, or equivalent combination of education and experience. • ASNT Level I (American Society for Nondestructive Testing) preferred., • AWS Certified Welding Inspector (American Welding Society) preferred., • CWB Certified Welding Inspector/Supervisor preferred., • NACE Certified Coating Inspector Level I (National Association of Corrosion Engineers) preferred., • USACE Certifications (United States Army Corps of Engineers) preferred. Growth Opportunities Alberici invests heavily in our team members training and development in both technical, management, and leadership aptitude. This role is on the quality department career ladder; employees participate in a Professional Development Plan (PDP) focused on career advancement. Typical growth opportunities for this position include: • Quality Manager Alberici is a North American company with multiple Operating Companies: Alberici Constructors, Inc., Alberici Constructors, LTD., Alberici Construcciones, BRC, CAS Constructors, Filanc, Flintco, Hillsdale Fabricators, and Kienlen Constructors #LI-Onsite

Job DescriptionStructural Fabrication Welder — Custom Assemblies Pay: $20.00–$25.00/hour (DOE) | Schedule: Full-Time | Location: Pevely, MO A Day in the Shop Your day starts by pulling a fresh set of prints, staging individual cut pieces, and planning the build. You’ll lay out structural tubing, square and align components, tack with intention, and then weld-out the assembly. Along the way you’ll verify dimensions, make adjustments to keep everything true, and finish with a complete, spec-ready structure. No two builds are exactly the same—this is hands-on, custom fabrication from first layout to final weld. Core Responsibilities • Read and interpret fabrication drawings, blueprints, and precise measurements., • Lay out parts and build assemblies from individual cut materials., • Fit, align, and square structural tubing and fabricated components., • Tack, weld, and join multiple sections to form complete assemblies., • Check dimensions and overall fit throughout the build; adjust as needed to meet specs., • Work independently from prints with limited supervision., • Maintain a clean, safe, organized work area.What You Bring, • Hands-on welding and metal fabrication experience., • Proven skill fitting and assembling structural or fabricated components., • Fluency reading blueprints/fabrication drawings., • Confident with a tape measure and basic shop math., • Ability to visualize how individual pieces come together into a final assembly., • Strong understanding of fit-up, alignment, and squareness in fabricated structures., • Comfort working with structural tubing and related materials., • Quality-driven mindset suited to non-repetitive, custom work.Backgrounds That Thrive Here Experience as a Welder/Fabricator, Fitter/Welder, Structural Fabricator, Fabrication Welder, or Welding Assembler is ideal. Candidates from custom fabrication, structural fabrication, equipment manufacturing, or any setting where welders build complete assemblies from prints (rather than repeating a single production weld) excel in this role. Why This Role Stands Out This is true fabrication—not a production line. You’ll receive drawings and materials and own the process of building finished welded assemblies from the ground up. If you enjoy reading prints, fitting complex structures, and taking pride in a complete build, you’ll feel right at home.

Job Description At Trinity Products, we’re more than a steel fabrication company — we’re a 100% employee-owned team driven by pride, precision, and performance. Our people take ownership of their work, support one another, and take pride in producing high-quality steel products. As a Mill Fabrication Welder on 2nd Shift (Monday - Thursday, 3:00pm – 1:30am), you’ll play a vital role in fabricating, preparing, welding and finishing steel products. Trinity Products are built with skill and built for what's next! Your expertise will help turn steel into solutions built for some of the most demanding projects. If you're a skilled welder who takes pride in quality workmanship, has an eye for detail, and is ready to contribute to a team that truly values your craftsmanship—this is the job for you! What You'll Do: • Perform weld preparation, welding, and finishing tasks in accordance with detailed specifications, blueprints, and drawings., • Interpretation of mechanical drawings, including weld requirement symbolism., • Set up and fine-tune welding fixtures and parameters, including amps, volts, and positioning for optimal welds., • Execute grinding, fitting, and finishing operations using manual and power tools for a clean, polished result., • Use of power tools to properly prep joints for welding., • Operate and maintain welding equipment to ensure safe and effective performance., • Use precision measuring instruments such as calipers and micrometers to inspect and verify work., • Follow all safety protocols and maintain a clean, organized work environment., • Use of an overhead bridge crane to safely move heavy, large steel materials. Requirements: • A minimum of 1 year of welding experience across various techniques is preferred—bring your hands-on know-how to the table., • Prove your skills – Successful completion of an internal weld test is required to join our elite team of welders., • Experience with D1.1 structural welding code, application, and quality standards., • Must be able to identify small defects in materials and joints that could affect structural integrity, • Understanding three-dimensional space is essential for positioning materials and effective solutions., • Steel-toe boots, sleeved shirts, and a welding hood are required—your personal gear shows you're ready to get the job done right!, • We’ve got you covered with the rest: Trinity provides all essential PPE including a hard hat, safety glasses, ear protection, and protective gloves., • Experience operating an overhead crane is a big plus—but if you don’t have it yet, we’ll help you get there., • Comfortable working in varied ambient temperatures—you’re not afraid to tackle real-world conditions., • Able to stand, move, and stay active throughout your shift—this is a hands-on, on-your-feet kind of role., • We count on you —punctuality and dependability matter in a fast-paced production environment. Founded in January 1979 by Robert Griggs and a team of visionary partners, Trinity Products began as a bold dream fueled by hard work, innovation, and an unwavering entrepreneurial spirit. From those humble beginnings, we’ve grown into a national leader in steel and steel fabrication—thanks to our commitment to continuous improvement and delivering exceptional value to our customers. Today, Trinity is proud to be a 100% Employee-Owned Company, with nearly 280 employee-owners who are directly invested in our success. With six strategic locations across the country and a broad, flexible product line, we proudly serve a wide range of industries and markets nationwide. At Trinity, we believe our strength lies in our people. Our employee-owners are not just workers—they’re stakeholders, innovators, and the driving force behind our continued growth. If you’re looking to join a company where your contributions truly matter and your voice can shape the future, Trinity Products is the place for you. Why You'll Love Working Here: • Employee-Owned – Your hard work builds your future. As an employee-ow

Job Description Job Summary: Supports Facilities Services by maintaining maintenance and operation of heating, ventilation, air conditioning, refrigeration, boilers, chillers, and related equipment as assigned. Duties/Responsibilities: This job description is not to be construed as an exhaustive statement of duties or responsibility requirements. Employees may be required to perform other job-related instructions as requested by the supervisor, subject to reasonable accommodation. • Drives utility truck to various buildings, making daily checks of campus mechanical rooms by walking throughout buildings, basement to roof, to inspect operational equipment. Makes daily notations in equipment log., • Creates weekly reports pertaining to HVAC operations., • Responds to HVAC related calls over the radio or by work order. Completes daily work orders and records time spent on the job, description of the job done, and any invoices relating to the job., • Performs, documents, and creates preventative maintenance plan on all appropriate equipment., • Services pneumatic controls and digital controls by calibrating, adjusting, or replacing. Views various computer system screens to monitor temperature and humidity in buildings., • Services air handlers and fan coils by cleaning coils with detergent cleaners and washing off with high pressure water hose. Replaces paper filters with like size or cleans permanent filters with detergent and water., • Using manifold gauges checks freon charge on aid conditioning compressors. Repairs units by replacing expansion valves, fan switches, belts, and thermostats., • Brazes and solders copper pipe using torch. Replaces plastic piping, metal piping, and copper piping using hand and power tools., • Use volt/Multi meters to troubleshoot various mechanical equipment (pumps, motors, fans). Wires equipment (if replacing) and follows wiring diagrams to troubleshoot and replace., • Cleans boilers by using wrenches to remove hatch bolts to open covers over water and fire tubes. Using wire brushes and high-pressure water hose flushes out scale and debris. Installs gaskets and steel washers to close boiler and return to service., • Using tech manuals and parts catalogs, orders parts and materials from equipment and parts vendors. When working on building heating and cooling systems, blueprints are used to determine function and layout., • Regularly monitors and checks for proper operation of pressures and temperatures., • Performs other duties as assigned.Required Skills/Abilities: To perform this job successfully an individual must be able to perform each essential duty satisfactorily. All job requirements listed indicate the minimum knowledge, skills, and/or ability deemed necessary to perform the job proficiently. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. • Specialized training in HVAC and 5 years of related experience; or an equivalent combination of education and experience., • EPA Certification required., • This position is included in the emergency and on call process. Must be able to provide a valid cell phone number or contact number where employee can be reached in the event of a campus emergency., • Knowledge of electricity, voltage, and amperage to work on motors and compressors., • Knowledge of welding and soldering to repair boilers and air conditioning., • Knowledge of plumbing for installing piping, drains, valves, and fittings., • Knowledge of. all compressor types, • Math skills are necessary for calculating HVAC loads, duct sizing, and more., • Ability to write for preparing daily work reports, equipment logs, and parts orders., • Ability to operate a truck for travel on campus or around city., • Ability to operate a gas-powered high-pressure washer., • Ability to use an arc welder to join steel., • Ability to use multi-meter, volt gauge, and amp probe to read electric loads., • Ability to use hand tools for repairing equipment., • Ability to use power tools including drill motors, Sawzall, grinder, and hammer drill., • Ability to crawl, stoop, and bend to make repairs., • Ability to climb ladder to work on high equipment or roofs., • Ability to walk from one building to another., • Ability to walk up and down stairs to check equipment., • Ability to see for operating equipment, machinery, trucks, and computers., • Ability to lift and carry up to 60 pounds for transporting tools, motors, chemicals, etc., • Ability to distinguish colors when wiring equipment., • Ability to read directions on equipment labels and for measuring chemicals., • Ability to be on call for afterhours repairs., • Ability to be alert and coordinated for thinking and reacting quickly., • Ability to responsibly drive a Drury University vehicle. Must possess a valid Missouri driver license and acceptable driving record. Education and Experience: • Specialized training in HVAC and 5 years of related experience; or an equivalent combination of education and experience., • EPA Certification required. Physical Requirements: The physical demand described here are representative of those that must be met by an employee to successfully perform the essential function of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is frequently required to stand, walk, use hands to finger, handle, or feel; reach with hands and arms; climb or balance, stoop, kneel, crouch, and crawl. The employee is occasionally required to sit; talk or hear; and smell. The employee must occasionally lift and/or move up to 60 pounds. Specific vision abilities required by this job include close vision, color vision, peripheral vision, and depth perception. While performing the duties of this job, the employee is regularly exposed to outside weather conditions. The employee is frequently exposed to moving mechanical parts and fumes or airborne particles. The employee is occasionally exposed to wet and/or humid conditions; high, precarious places; toxic or caustic chemicals; risk of electrical shock; and vibration. The noise level in the work environment is usually loud. WORKING AT DU HAS ITS BENEFITS: • Generous time off including 4+ weeks of paid time off starting your first year, • Free tuition for your whole family, • Free tickets to Drury home sporting events, • Health and wellness benefits at extremely competitive rates, • Free use of onsite fitness center on Springfield campus, • Discounted meals and Drury merchandise on campus

Job Description JUMPSTART, ADVANCE, AND LOVE YOUR CAREER WITH SMSI! At SMSI, we believe in our employees; with above-average pay, extensive benefits, vocational training, and a family-based atmosphere, we are always looking for people seeking to improve themselves. Together, our team strives to provide the best service possible for customers. We thrive on challenges and believe in fair compensation for dedication, attention to detail, and professionalism. We are seeking an experienced Structural/ Pipe Fitter to join our team! Compensation will be determined based on the candidate's experience and qualifications. Compensation: $23 - $24 hourly Responsibilities: Fit and weld stainless steel and steel products (heavy and light gauge) to specification Adhere to the blueprints to fulfill the product specifications Determine material dimensions to confirm requirements Inspect and examine parts to ensure they meet the quality standards and expectations Ensure that equipment and tools are used and kept in good working order for longevity of tool life and safety purposes This position is safety-sensitive Qualifications: • Prior experience in fabrication, welding, manufacturing, or a related field, • Proficient in welding GTAW, GMAW, and SMAW, • Strong capabilities in interpreting engineering blueprints and drawings, • Experience with fabrication and hand tools, • Excellent understanding of various types of metal and their respective properties, • Capacity to manage physical demands, • Familiarity with Safety regulations and readiness to utilize personal protective Equipment (PPE) such as safety glasses, face shields, gloves, and steel-toed boots., • Experience with painting, breaking, and rolling is a PLUS, and willingness to be a backup for these positions. About Company SMSI is dedicated to providing the highest quality mechanical services performed in an honest, dependable, and efficient manner. SMSI offers lots of room to grow in a fast-paced company. We have been serving commercial and industrial markets for 30 years.

Job Description Job Summary Nothum is seeking a skilled welder to work in a team environment, assisting in the welding process for large-scale machinery. This role requires precision, strong attention to detail, and adherence to safety standards. Key Responsibilities • Perform welding processes for large-scale machinery., • Ensure assigned weldments are completed accurately and efficiently., • Measure and square assemblies for proper alignment., • Follow blueprints and supervisor instructions; seek clarification when needed., • Execute physical tasks including standing, stooping, bending, sitting, and crawling., • Lift and move up to 50 lbs; heavier loads require assistance., • Utilize required PPE, including safety glasses, weld hood, and steel toe boots., • Complete additional responsibilities as assigned., • Tier 1 Responsibilities: Weld out frames, weld AcuFeeders, install doors, and heat exchanger stacks. Qualifications • Prior welding experience (TIG preferred)., • Ability to read and interpret technical blueprints., • Strong attention to detail and craftsmanship., • Understanding of welding safety procedures., • Team-oriented mindset with a strong work ethic., • Must complete a weld test as part of pre-employment screening. Benefits • Employee Ownership Program – Be part of a company where your contributions matter., • Competitive pay and benefits package., • Opportunities for growth and advancement. Join our employee-owned team today!

Job Description SFI is looking for Welders with 3 years or more experience in tank building. General Summary: • Lays out, fits, and welds fabricated, cast, and forged components to assemble parts or tanks, with assistance from Bay Supervisor or Master Craftsman. This position is classified as a safety sensitive position, see Limitations and Disclaimer for additional information. Essential Job Functions: • Studies engineering drawings and blueprints, locates and marks bending and cutting lines, and lays out and examines metal stock to ensure specifications are met., • Aligns and fits parts, moves parts into position, and secures parts for welding., • Verifies conformance of workpieces to specifications, and prepares completed work to be checked by supervisors., • Sets up and operates fabricating machines and welding equipment., • MIG, TIG, Flux, Core, stick, and tack-welds parts and tank seams., • Completes manufacturing documentation in a timely manner., • Follows all safety guidelines as noted in Safety Manual., • Assists all supervisors and performs other duties as needed and directed. Knowledge, Skills, and Abilities: • Must be able to pass all basic Welder tests as well as pass GTAW, GMAW, FCAW processes., • Knowledge of design techniques, tools, and principles involved in production of precision technical plans, blueprints, drawings, and models., • Knowledge of welding/grinding procedures., • Must be able to layout, fit up and weld heads, shells, legs and parts on a tank., • Must be able to burn and prep the holes for fitting., • Ability to read cut sheets, blueprints, and tape measures, • Ability to keep hand and arm steady when moving or holding arm and hand in one position., • Ability to meet budgeted hours. Education and Experience: • High school diploma or general education degree (GED); or 3+ years related experience and/or training; or equivalent combination of education and experience. Working Conditions: • While performing the duties of this job, the employee is regularly exposed to moving mechanical parts; fumes or airborne particles and vibration. The employee is occasionally exposed to high, precarious places and toxic or caustic chemicals., • The noise level in the work environment is usually loud., • The employee must frequently lift and/or move up to 25 pounds and occasionally lift and/or move up to 50 pounds. Limitations and Disclaimer: The above job description is meant to describe the general nature and level of work being performed; it is not intended to be construed as an exhaustive list of all responsibilities, duties, and skills required for the position. All job requirements are subject to possible modification to reasonably accommodate individuals with disabilities. Some requirements may exclude individuals who pose a direct threat or significant risk to the health and safety of themselves or other employees. Safety sensitive jobs are those with tasks or duties that reasonably could affect the health and safety of the employee and others. Safety sensitive jobs include, but are not limited to, jobs that use heavy machinery, use power tools, operating public transportation or dealing with hazardous chemicals. Employees hired to safety-sensitive positions must submit to regular drug and alcohol testing, as well as post-accident testing. This job description in no way states or implies that these are the only duties to be performed by the employee occupying this position. Employees will be required to follow any other job-related instructions and to perform other job-related duties requested by their supervisor in compliance with Federal and State Laws. Requirements are representative of minimum levels of knowledge, skills and/or abilities. To perform this job successfully, the employee must possess the abilities or aptitudes to perform each duty proficiently. Continued employment remains on an “at-will” basis. Day Shift - Monday -Thursday 7am-5:30pm Night Shift - Monday - Thursday 6pm-4:30am Weekends - Friday/Saturday/Sunday 6am-6:30pm $25-$30 per hour based on skills

Job Description Primary Function: Attach wax patterns to a sprue stick, exercising care to complete a difficult, and / or heavy, quality assembly Tools and Equipment: Hot irons, clippers, hot wires, rework tools, angles, Bunsen burner, holding racks, spacers, putty knives, electronic media, H2O welder, etc. Material: Various types of pattern wax, stictite, ceramic pouring cups, sprue handles, etc. Working Procedure: With the guidance and supervision of the department supervisor and/or the Senior Assembler THE FOLLOWING ARE THE USUAL MAJOR JOB DUTIES BUT THIS JOB DESCRIPTION DOES NOT PRECLUDE THE PERFORMANCE OF OTHER DUTIES BY THE INCUMBENT. 1. Shall adhere to all safety requirements as posted on the job safety card., 2. Shall receive daily work assignments from the department supervisor or the department group leader. 1. Shall consistently follow all applicable work instructions., 2. Shall assemble sprues in accordance with electronically provided work instructions, where the size and fragility of the wax patterns, and the difficult gating require extreme care to complete a quality assembly.5. Shall hang all completed assemblies on conveyor after careful inspection. 1. Shall attend and successfully complete hazardous material / waste handling classes., 2. Shall maintain all labor vouchers, records, and files, in addition to a variety of logs where accuracy is paramount, and enter all required information into the Company software in a timely manner. 1. Shall attend and successfully complete lockout / tag out training classes., 2. Shall maintain work area in a clean and orderly condition., 3. Shall attend and successfully complete training in the proper techniques of lifting., 4. Shall perform other duties as assigned. Work Environment: Work is to be performed in an air-conditioned environment, as free as possible of contaminants. Special Skills Required: Must have sufficient strength and manual dexterity to perform the physical demands of the job. Must have average working knowledge of personal computers and related software.

Job Description Warehouse Staff Job Description $22.00/HR Full Time SPS Fire Protection is seeking a full-time shop/warehouse employee for our growing Blue Springs, MO location. We provide premier fire protection products and fabrication to the greater KC area, as well as surrounding states from this location. This candidate will be required to lift 70lbs on occasion as well as operate various machinery used to fabricate pipe and related products. A strong mechanical aptitude, including the ability to be trained to operate our equipment, is necessary for this position. Any welding experience would be a plus as there is also currently an opportunity for a backup welder. Full Time position Monday through Friday, 7AM – 3:30PM. This is a union shop, which is currently in the second year of a 3-year agreement. The top scale is $28.75 currently. Starting salary is $22.00 per hour, with increases yearly at contract raise which is April 1. SPS offers 7 paid holidays per year.

Job Description Job Summary: Responsible for ensuring Martinrea and Customer quality requirements are met while welding materials into parts. Required Education and Experience: Must have a current AWS certificate Sound understanding of Welding Metallurgy Fundamental understanding of NDE techniques Sound understanding of Gas Metal Arc Welding, Projection and Resistance Welding Manual GMAW experience Working experience with industrial robots Must have good interpersonal and communication skills. Good problem solving skills Must be willing to work shifts and be flexible (including overtime on short notice) Ability to work well with fellow team members and promote "Team" concept Basic knowledge of ISO/TS 16949:2002 an asset Basic knowledge and use of measuring equipment Basic Computer skills Understanding of Core Skills and basic GD&T Basic understanding of CMM Essential Functions: Perform all duties and promote them in a manner that reflects the Martinrea Expectations, through Martinrea Employee Charter. Contribute to continuous improvement and cost reduction activities. Support the WEC's on new and existing programs Support Buy offs when required Keep the product cleaned up in quarantine Establish, maintain and implement welding parameters to support production and Quality Assurance Conducts weld inspection and analyze weld data, generate reports Assist with Robotic weld touchups Archiving and maintaining Paxit system Be dedicated to generating and or assisting in PPAP packages when required Maintain a sound understanding of customers' product and engineering specifications Participate in problem solving activities Participate in Product, System and Process Audits as required Assist in the training of production personnel in all quality requirements when required Attend and or Champion quality meetings when requested Provide support to all Departments for weld related issues Cover for the other Technicians if he/she is absent Generating and upkeep of the Weld Set up Instructions, Weld Inspection Records and Weld Length records Ability to work well in a team environment or individually Audit and approve Special Material Requests and reworked material when required Initiate and coordinate problem reports and containments Buy off of the First-Off / Mid-Off processes, and set up verifications to ensure it is being done correctly Demonstrate a sense of urgency to achieve results Take initiative to follow through on completion of tasks / projects, PMR's and CIP'sAbide by all Company polices including, but not limited to the following: Health and Safety, Quality and Environmental Systems, Human Resources policies, and the Martinrea Employee Handbook • Compliance with Company policies concerning applicable laws Work Environment: • Both office setting and production environment, • Constant communication with employees, peers, and management, • Flexible hours as required Physical Demands: • Ability to work on computer for long periods of time, • Ability to be present on the production floor on a daily basis Health and Safety: • Must work in accordance with Health and Safety regulations, Company and plant rules, policies and procedures, • Must use or wear Personal Protective Equipment and certain clothing as required by the Company Other Duties: • This job description is not designed to contain a comprehensive list of duties and responsibilities required for this job. Duties and responsibilities may change at any time with or without notice

Job DescriptionDescription: The Welder/Fabrication/Maintenance Worker is responsible for fabricating and welding unique parts and assemblies required in all areas of the scrapyard. • Safety in the welding and fabrication division must be observed and practiced at all times. Additional PPE’s such as welding hoods, welding gloves, leather clothing, and full face shields (along with safety glasses) are required., • The use of specialty welding equipment is required in this division and all manufacture safety procedures must be adhered to at all times., • All specialty equipment must be checked for damage and repaired if damage exists before each use., • The Welder and Fabrication Worker is responsible for fabricating and welding specialized assemblies to replace parts that have been worn past their usable life., • Repair and fabricate various size trailers used to haul scrap metal material from commercial and industrial accounts., • Repair various size metal containers, used by roll off trucks to haul scrap metal from commercial and industrial accounts., • Assist on shredder maintenance and repairs when directed., • Clean and maintain the welding area, using whatever resources are necessary, to remove objects, debris and hazards from the work area., • Secure all high pressure cylinders., • Practice safe welding and torching processes at all times., • Ensure a clean, safe and orderly workplace; clean and prepare sites by removing debris and possible hazards., • Properly follow company and OSHA safety procedures., • Follow instructions from Shredder & Maintenance Superintendent., • Adhere to operating and health and safety protocols., • All other duties as assigned.Requirements: Qualifications • Must be safety minded. Must understand and abide by all safety rules and regulations., • Must have working knowledge of safe welding and torching practices., • Must be organized and keep a clean and safe work area., • Minimum of 3 years welding experience., • Ability to use variety of hand tools required for fabrication, welding and repairs., • Must work independently as well as within a team environment., • Welder and fabrication Worker must be able to frequently lift and carry up to 50 pounds., • Must be able to work overhead, climb ladders, kneel, and stand for long periods., • Ability and desire to work in all weather conditions including rain, snow, cold and heat., • Ability to communicate effectively.

Job Description Overview: We are hiring dependable and hardworking individuals for Assembler, Welder, and Quality Assurance Technician positions with a manufacturing company in Riverside, MO. These are hands-on roles in a production environment with opportunities for overtime and advancement. Skills and Experience: • Manufacturing or production experience, • Assembly and mechanical experience, • Welding or fabrication experience, • Ability to read blueprints, work instructions, and measurements, • Experience using hand and power tools, • Quality control and product inspection experience, • Ability to identify defects and quality issues, • Experience using measuring tools such as calipers or gauges, • Ability to document inspection results, • Strong attention to detail, • Ability to troubleshoot basic production issues, • Ability to follow safety procedures, • Ability to work independently and as part of a team, • Ability to stand, bend, lift, and perform repetitive tasks, • Previous experience in a manufacturing environment required Benefits: Don't miss this chance to enhance your experience in a production environment while enjoying competitive pay and a comprehensive benefits package. • Weekly pay, • $5 prescription drugs, • $5 doctor's visit copays, • Free teledoctor service, • Free counseling services, • Life insurance included, • Vision insurance included, • Dental insurance included, • Vacation and holiday pay, • Scholarship Opportunities, • 401(k) retirement plan, • Free legal services, • Our unbeatable employee discount program Apply with resume now so we can hold a spot for you. We can’t wait to talk to you! ––Your Ōnin team

Job DescriptionPrecision TIG Fabrication Welder (Stainless & Carbon) Do you read blueprints like a second language? Can you switch from a tight-root pass on pipe to a clean cap on a stainless assembly without missing a beat? Are you equally at home with GTAW and FCAW in flat, vertical, overhead—and 6G? If you answered yes, read on. Role focus • TIG/GTAW welding on stainless and carbon steel for pipe, tubing, machinery, structural components, and fabricated assemblies., • Flux Core (FCAW) welding when production or process demands it., • Full-position welding: flat, horizontal, vertical, overhead, and 6G., • Equipment setup and optimization: amperage, filler/wire, tungsten, shielding gas, and technique., • Blueprint and welding symbol interpretation; working to dimensions, tolerances, and specifications., • Fit-up, alignment, positioning, and tacking of components before welding., • Pipe and structural fabrication per drawings; proper use of calipers, tape measures, squares, levels, and straightedges., • Heat control to limit distortion; grinding, cleaning, prep, and finishing to spec., • Weld inspection for quality, penetration, defects, and compliance., • Operate hand/power tools common to fabrication; maintain welding equipment and report issues., • Meet safety, quality, and production requirements while communicating effectively with the team.Must-have qualifications, • 3–5 years of professional TIG/GTAW experience., • Proven TIG capability on stainless and carbon steel., • Flux Core (FCAW) welding experience is required., • Pipe and/or fabricated metal welding background with 6G proficiency., • Skilled in reading drawings, weld symbols, and technical documentation., • Experience in fitting, fabrication, layout, and assembly., • Knowledge of specs, dimensions, tolerances, and quality criteria., • Strong tool knowledge and accurate use of measurement equipment., • Detail focus, problem solving, and clear communication., • Ability to work independently and in a production team environment., • Ability to work overtime or occasional weekends as required.Pass these tests to proceed, • 2-inch Schedule 160 carbon steel pipe – TIG, 6G position, • ¼-inch Schedule 80 carbon steel pipe – TIG, 6G position Successful completion of both TIG tests is required for consideration. Preferred background • TIG on 304/316 stainless; thin-gauge stainless expertise., • Carbon steel pipe welding and additional FCAW experience., • MIG/GMAW alongside TIG and Flux Core., • Sanitary/food-grade, industrial, or precision fabrication work., • Pipe fitting and fabrication experience., • Manufacturing/industrial welding environments; comfort with detailed fab drawings and specs.Physical & environmental expectations, • Extended standing with frequent walking, bending, kneeling, crawling, and reaching., • Exposure to moderate–high noise in a manufacturing environment., • Frequently lift/move up to 60 pounds., • Operate safely around welding equipment, hot work, sparks, fumes, and moving machinery., • PPE required at all times; follow all safety procedures.Who we are Express Employment Professionals partners with talented tradespeople and outstanding companies. We align your skills with high-quality opportunities and provide reliable staffing solutions to our clients. Express Employment Professionals is an Equal Opportunity Employer. M/F/Vet/Disabilities Equipment you’ll operate • TIG Welder, • Flux-Cored Arc Welder

Job Description Looking for a skilled TIG Welder who can bring precision and excellence to metal fabrication? This exciting opportunity for a TIG Welder offers a chance to work on stainless steel and a variety of metals, demonstrating your expertise in a demanding and rewarding environment. As a key member of the team, the TIG Welder will interpret blueprints, set up and operate welding equipment, inspect welds for quality, and follow safety protocols. If you have a passion for craftsmanship and a keen eye for detail, this role is perfect for you! Required Skills: • Minimum of 3+ years of TIG welding experience, • Proficient in welding stainless steel and thin-gauge materials, • Ability to read technical drawings and interpret welding symbols, • Strong attention to detail and quality control, • Physical ability to lift up to 50 lbs and work in a physically demanding environment, • Reliable, punctual, and committed to safety standards Nice to Have Skills: • Experience in fabrication and assembly of metal parts, • Ability to work collaboratively in a team setting Preferred Education and Experience: • Relevant technical training or certification in welding preferred, • Proven track record of delivering high-quality welds in a fast-paced environment Other Requirements: • Welding test required (50% markup / 480 hours), • Monday-Thursday schedule, 6AM-4:30PM, with occasional Friday overtime, • Must maintain a clean and organized work area Salary Range: $25–$30 per hour DOE Seize this opportunity to advance your career as a TIG Welder—apply today and bring your expertise to a dynamic team committed to excellence! Allied OneSource is connecting great people with great opportunities. #ZR

Job Description WEG Transformers USA Description: Description Pay / Benefits: Pay: $24.01 - $25.49 / hour ($24.01 - $25.49 + $0.75 / hour shift premium) Benefits: WEG offers competitive compensation, meaningful and exciting career options, as well as excellent benefits, including: • Paid Vacation & Holidays, • Excellent Medical, Dental, and Vision coverage starts at 30 days., • 401(k) with Match, • Tuition Reimbursement, • Employee Assistance Program (EAP), • Company paid life & disability insurance., • Bonus Plan (pro-rated) Specific details & more in the WEG Transformers USA & IUE-CWA CBA, 2021. WEG: Our Company Founded in 1961, WEG is recognized as one of the largest electric machine manufacturers in the world. WEG employs over 40,000 people around the globe and offers a diversified and integrated product line, with sales to more than 135 countries worldwide. Our U.S. operations are growing at an impressive rate and we're looking for talented individuals to help us move forward with this aggressive growth plan. WEG is committed to building quality products and providing efficient solutions. To achieve this goal, we strive for continuous investment in innovation and team work. Helping people reach their goals by living the values of the company is a passion shared by everyone at WEG. At WEG, our Values stand as: Human Company, Team Work, Efficiency, Flexibility, Innovation and Leadership. As a Human Company, we value each individual contribution to our success, and we motivate people by means of integrity, ethics and constant support to personal development. WEG, also, supports Green Initiatives such as the implementation of a company-wide recycling program, the use of green chemicals for office cleaning, the elimination of Styrofoam cups, and installation of HVAC economizers on rooftop units and an energy management system to improve overall energy efficiency. Role: Welder In this role, you will: • Set-up and operate MIG welding machines, adjust machine and wire feed as required., • Normally welding on 16 gauge to 10-gauge mild steel, attaching accessories and fittings or seam welding on parts., • Work from layout marks, simple drawings., • Use scale, square and power tools., • Assemble and tack weld repetitive jobs, finish weld, tack welded assemblies, usually in down and or vertical position., • Operate grinder to clean and shape weld., • Conduct visual and dimensional check of own work., • Support WEG's 5S program in an effort to maintain work area, equipment and supplies in a neat, organized manner., • Notify supervisor of material shortages or other concerns., • Work safely in required PPE to manufacture a high-quality component of a transformer. WEG offers competitive compensation, meaningful and exciting career options, as well as excellent benefits, including paid vacation, medical, dental, vision, 401(k), flexible spending accounts, life insurance, and disability. Apply Today: Do you have passion for making things right the first time? Do you enjoy welding? Do you want to be part of a growing company? If you answered "Yes" & meet our qualifications, we invite you to apply today to join the WEG Team! https://weg.us/ Prior to the next step in the recruitment process, we welcome you to inform us confidentially if you may require any special accommodations in order to participate fully in our recruitment experience. Please contact us at 1-663-239-9300 should you need a referral to the recruiter for this requisition. No 3rd Parties / Recruiters, please. Requirements: Basic: • Prior welding experience., • Able to work overtime as needed., • Ability to work evening or night shift., • Must be able to read, write and comprehend common vocabulary., • Must be able to calculate basic math, including fractions, decimals and percentages., • Must be able to read, interpret and work from blueprints, sketches, wiring diagrams, plans, layouts and/or templates., • To move forward in the process, candidates will successfully complete: an application, welding knowledge & skill assessments, talent assessment, interview, drug and background screening., • Safety Sensitive position: Drug panel includes THC., • Resides within a reasonable commuting distance of Washington MO., • Legal authorization to work in the United States on a permanent basis; visa sponsorship is not available for these positions. Preferred: • High school diploma or equivalent., • Participation in Future Farmers of America (FFA) or 4-H Welding projects / programs., • Completion of Welding Trade school and/or Apprenticeship program., • Two years of prior manufacturing experience. Compensation details: 24.01-25.49 Hourly Wage PId505eaa88ecb-25405-41478589

Job Description Job Summary: Supports Facilities Services by performing various maintenance functions, such as HVAC, electrical, carpentry, plumbing and miscellaneous duties as assigned. Performs routine and emergency situations with minimal supervision and follows established, standard practices. Duties/Responsibilities: This job description is not to be construed as an exhaustive statement of duties or responsibility requirements. Employees may be required to perform other job-related instructions as requested by the supervisor, subject to reasonable accommodation. • Under the direction of an assigned supervisor, perform general repair and maintenance on structures, facilities, and equipment., • Perform preventive maintenance on structures, facilities, and equipment according to established schedules., • Perform routine installations and repairs and systems maintenance duties in assistance to skilled maintenance personnel in projects involving specialized trades to include electrical, plumbing, flooring, roofing, drywall, HVAC, carpentry, and masonry., • Respond to emergency request to perform routine repairs and adjustments to buildings and facilities., • Install shelving and bulletin boards, repair desk, chairs, and other furniture and equipment., • Maintain routine records and logs related to maintenance and repair activities., • Perform related duties as assigned., • Attends all assigned meetings., • Using computers in facilities services break room, submits all time off requests in a timely manner complying with departmental policy.Required Skills/Abilities: To perform this job successfully an individual must be able to perform each essential duty satisfactorily. All job requirements listed indicate the minimum knowledge, skills, and/or ability deemed necessary to perform the job proficiently. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. • High school diploma or equivalent and five years of related experience or equivalent combination of education and experience. License/certification in electrical/HVAC/mechanics or welding preferred., • Ability to drive vehicle on campus. Must have valid MO driver’s license and acceptable driving record., • This position is included in the emergency and on call process. Must be able to provide a valid cell phone number or contact number where employee can be reached in the event of a campus emergency., • Ability to operate a forklift and use equipment, machines, and tools for general maintenance and repair work., • Knowledge of electricity and the ability to connect and disconnect wire equipment., • Knowledge of gas and the ability to connect and disconnect pipe equipment., • Knowledge of water and the ability to connect and disconnect pipe equipment., • Knowledge of welder and torch and the ability to join steel, copper pipe., • Knowledge of small hand tools and the ability to assemble and disassemble equipment., • Knowledge of volt gauge and amp probe and the ability to read electric current., • Knowledge of manifold gauge and the ability to measure coolant., • Knowledge of drill, motor and grinder and the ability to fabricate parts., • Ability to be alert and coordinated in order to think and react quickly., • Ability to read equipment labels and mixing directions., • Ability to identify colors in order to identify wire equipment and test chemicals., • Ability to prepare written logs and order parts., • Knowledge of math and the ability to calculate mixtures., • Knowledge and understanding of mechanics of lock systems. Education and Experience: • High school diploma or equivalent and five years of related experience or equivalent combination of education and experience. License/certification in electrical/HVAC/mechanics or welding preferred. Physical Requirements: The physical demand described here are representative of those that must be met by an employee to successfully perform the essential function of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions. While performing the duties of this job, the employee is frequently required to walk; reach with hands and arms; climb or balance; and stoop, kneel, crouch, or crawl. The employee is occasionally required to stand; use hands to finger, handle, or feel; and talk or hear. The employee must frequently lift and/or move up to 50 pounds and occasionally lift and/or move up to 100 pounds. Specific vision abilities required by this job include close vision. While performing the duties of this job, the employee is regularly exposed to outside weather conditions. The employee is frequently exposed to moving mechanical parts and fumes or airborne particles. The employee is occasionally exposed to wet and/or humid conditions; high, precarious places; toxic or caustic chemicals; risk of electrical shock; and vibration. The noise level in the work environment is usually loud. WORKING AT DU HAS ITS BENEFITS: • Generous time off including 4+ weeks of paid time off starting your first year, • Free tuition for your whole family, • Free tickets to Drury home sporting events, • Health and wellness benefits at extremely competitive rates, • Free use of onsite fitness center on Springfield campus, • Discounted meals and Drury merchandise on campus

Job Description Classification: Non-Exempt We are Alsco Uniforms. We’ve been working hard for our customers since 1889 when we invented the uniform and linen rental industry. Alsco Uniforms has grown into a worldwide leader serving over 350,000 customers in 13 countries. It’s our job every day to make every aspect of the customer experience better. Whatever our customers need, Alsco Uniforms finds the answers that work for them. Our employees are the heart and soul of Alsco Uniforms. As a result, we have a long history of strong financial performance, continuous improvement, and customer service. We’re seeking driven professionals with ambition to grow within our company. We’d love to talk to you about how you can fit into our team of diverse individuals and how your hard work will be rewarded with competitive pay and benefits and ongoing career development. Join our team and build your career with Alsco Uniforms! Job Summary: The Maintenance Technician is responsible for installing, repairing and maintaining large industrial textile processing equipment, as well as facility maintenance. Tasks include start-up and shut-down procedures, electrical troubleshooting, maintaining and operating boilers, welding and cutting, hydraulics, pneumatics, mechanical, and other systems. This position reports to the Chief Engineer. Hourly base pay: $34.00-$38.00 Our full-time employees enjoy: • 401K Plan with Company Match, • Medical, Dental, Vision, FSA/HSA, • Life Insurance, Disability Insurance, • Vacation, Sick Time, Holidays, • Choice of Global Cash Card or Direct Deposit, • Career Advancement, • Learning & Development Opportunities, • Inclusive and Diverse Team Environment Benefits may vary for positions covered by a collective bargaining agreement. Essential Functions: • Installs, repairs and performs preventative maintenance on industrial processing equipment, water levels, water systems and other equipment and systems., • Troubleshoots electrical issues., • Responds to daily maintenance requests in a timely fashion to minimize equipment downtime., • Provides emergency/unscheduled repairs of production equipment., • Diagnoses problems, replaces or repairs parts, tests and makes adjustments., • Looks for opportunities to continually improve maintenance processes., • Works with all plant personnel in a cooperative and professional manner., • Strictly adheres to all safety rules, policies and procedures required by Alsco, law, and what is recognized as common practice in the industry., • Ensures work is performed safely and efficiently., • Maintains technical knowledge by attending educational workshops and reviewing technical publications. Remains current on equipment and repair procedures and best practices., • Studies blueprints and manufacturers’ manuals to determine correct operation of machinery., • Proficient in reading electrical schematics., • Maintains accurate and timely records of maintenance performed., • Follows written and verbal instructions and performs other tasks as directed by supervision., • Complies with all Federal, State and local laws. Additional Functions: • May work with and support other branch personnel as required by supervision., • Drive and pick up parts, transport equipment, parts, etc. Qualifications: • Have and maintain a valid driver’s license and driving record free of chargeable accidents, speeding or other safety violations., • Minimum of two years maintenance engineering experience with specific knowledge of machinery, electricity, electronics, plumbing, hydraulics, pneumatics, welder and boiler applications., • Proficient in the proper use of power and hand tools., • Strong electrical troubleshooting ability of 3 phase 230 volt systems., • PLC programming experience., • Experience in carpentry, boiler repair, welding, and general facility repairs., • Good verbal and written communication skills in English, ability to comprehend and follow direction, perform basic math, good time management, • Must be a team player with enthusiasm, initiative, and pride in work well done; self-starter dedicated to continual quality improvement. Education: • High school graduate or equivalency preferred., • Some locations may require relevant certifications, a boiler license or PLC programming. Typical Physical Activity: • Standing, sitting, walking, bending, stooping, reaching, twisting, kneeling, working in confined areas, reaching overhead, driving a forklift, grasping, moving equipment, pushing, pulling, moving loaded carts weighing up to 500 lbs, lifting and carrying up to 100 lbs, reading, writing, speaking, hearing. Typical Environmental Conditions: • Inside and outside areas of a typical industrial laundry facility, which includes working with and around large machinery, variations in temperature, noise, odors, humidity, lint and dust, in general offices or on outside grounds. Travel Requirements: • Occasionally, such as to procure parts. The Maintenance Technician must perform the essential duties and responsibilities with or without reasonable accommodation efficiently and accurately, and without causing significant safety threat to self or others. The statements made herein are intended to describe the general nature and level of work being performed by employees assigned to this job classification. They are not intended to be construed as an exhaustive and inclusive list of all responsibilities, duties, and/or skills required of personnel so classified. For a general description of benefits that are being offered for this position, please visit alsco.com/benefits. Alsco Uniforms is an Equal Employment Opportunity Employer. Candidates are considered for employment with Alsco Uniforms without regard to their race, color, religion, national origin, age, sex, gender, pregnancy, disability, sexual orientation, gender identity, genetic information, military status, protected veteran status (specifically status as a disabled veteran, recently separated veteran, armed forces service medal veteran, or active duty wartime or campaign badge veteran), or other classification protected by applicable federal, state, or local law. Revised: 04/29/2022

Job DescriptionCompany Description WireCo® is the strength behind the world’s evolution, through deep legacy and forward thinking, we create premium ropes that inspire innovation without limits. Our global footprint includes manufacturing plants, distribution facilities, and research and development centers around the world. For more information, check out our website at www.wireco.com. https://youtu.be/zzplYW7PMFg https://www.youtube.com/watch?v=6CJwd_yXZAY Why You'll Love Working at WireCo • Pay for Skills Program – Earn more as you learn! Increase your earning potential by completing skill-based training and becoming qualified on additional equipment and processes., • Day One Benefits – Eligible full-time associates receive medical, dental, and vision coverage starting on their first day of employment., • 401(k) – Save for your future with a company match after 90 days of employment., • Monthly Incentive Program – Earn monthly incentive payments after successfully completing your 90-day probationary period., • Paid Time Off & Paid Holidays, • Company-Paid Life & Disability Insurance, • Employee Assistance Program (EAP)Job Description The Production Technician sets up and operates one or more wire drawing machines. Positions and secures specified dies in the dieholder, using hand tools. Lifts coil of wire onto feed reel and threads it through dies. Coats wire with lubricant to facilitate the drawing machine and starts machine. Inspects and measures drawn wire to verify conformance to specified shape, size and resistance, using instruments such as wire gauges and micrometers, and replaces worn dies by using hand tools. Performs tensile strength and other tests and records test data on proper form. The Production Technician must exhibit the behaviors of the WireCo Business System (WBS): • Teamwork - welcomes an environment of inclusiveness and healthy debate that reflects our team’s strength, • Accountable – celebrates our successes, learn from failures, avoid excuses, and own the outcomes of our efforts, • Self-Aware – demonstrates an understanding of our strengths and needs, considering how our actions impact others, • Noble Intent – acts in the interests of others, approaching our work with integrity to ensure the best outcome, • Determined – takes initiative, share ideas and find solutions to win and achieve our goals, • Transparent – promotes open and honest communication and constructive feedback for clarity and truth, • Curious – seeks knowledge and outside input to test our way of thinking, challenging the status quo Duties & Responsibilities • Inspects machine and equipment used to ensure safe mechanical operation. Makes minor maintenance repairs and reports any maintenance or safety problems that require corrective action., • Determines the size of wire to be run and verifies that machine dies are the correct sizes. Checks dies with micrometer for accuracy and replaces worn dies as needed. Checks rod or breakdown wire to conform with requirements and places in proper position on poles, stands, or flippers, using a forklift when necessary. Cuts tie wires, straightens tangled coils, and breaks down wire if a new setup is required; otherwise, welds the top of new material to the bottom of the material running out. Threads pointed end through die and around block in accordance with standard procedure or as directed by the Supervisor. Strings up the machine in prescribed manner., • Checks wire size and adjusts die boxes to obtain proper cast and cuts test samples. Gauges wire with micrometer, operates tensile and torsion machine to test samples, and records test data on form. Checks optical temperatures and wire speeds. Checks the weights of carriers or spools on special length jobs., • Checks wire tolerances after each spool, respool, or coil and sample. Records wire diameters on appropriate paperwork., • Repairs all breaks, exercising good judgment. Sets counter to prescribed count or standard setting. Changes heads, bonnets, pins and shafts, if necessary. Cleans water lines, steam nozzles, water jets, and water drains as needed. Maintains proper lubricants in all die boxes and replenishes as needed., • Removes spool or coil from the machine, replaces empty spool, starts machine, and ties up bundle or spool. Ensures that all material is properly tagged and placed on proper pallets or skids., • Checks machines, tools, and auxiliary equipment to be sure they are operating efficiently and safely. Performs minor maintenance to correct problems and ensures maintenance is notified of problems requiring corrective action., • Regularly performs safety inspections in the area and corrects problems where possible. Reports other problems to maintenance or Supervisor for corrective action. Responsible for housekeeping in the area., • Ensures all material is packaged according to customer specifications and is prepared for shipment. Loads and unloads trucks and keeps material in a neat and orderly manner. Inspects forklifts daily and logs inspection on proper form. Monitors and maintains proper fluid and fuel levels as required. Operates forklifts in a safe and orderly manner., • Assures that finished products meet quality standards and specifications., • Assists other employees in work group or other work groups as needed. Responsible for the pass down of operating information, problems, etc., to co-workers on the next shift., • Performs any other miscellaneous duties as assigned. Schedule: • M, T, W — 5:00 p.m. to 5:00 a.m., • Th, F — 7:00 p.m. to 7:00 a.m. Compensation: • $21.85/hour, • $1.00 shift differential + Monthly Incentive Payments based on meeting operational metrics after the 90-day probationary period is complete Earn More with WireCo's Q4 2026 Hourly Employee Incentive Program! At WireCo, we recognize employees who demonstrate reliability, dedication, and a commitment to helping their team succeed. During Q4 2026 (October–December), eligible hourly employees have opportunities to earn additional incentives beyond their regular wages and benefits. Perfect Attendance Bonus – Earn an Extra $100 Per Month! Eligible employees who achieve perfect attendance can earn an additional $100 per month during Q4 2026. Q4 2026 Performance-Based Incentives Employees who achieve perfect attendance may also qualify for additional performance-based incentives when the facility meets its monthly production utilization targets. Our Chillicothe facility offers: $2,000 site prize pool upon achieving the 90% utilization target. $8,000 site prize pool upon achieving the 95% stretch target. Eligible employees may participate in prize drawings, with bonus amounts dependent on plant performance. This incentive program applies to Q4 2026 (October 1–December 31, 2026). Eligibility requirements, performance targets, and additional terms and conditions apply. Contact WireCo HR for complete program details. Bonuses are not guaranteed. Prize pools are awarded through eligible drawings and do not represent guaranteed individual payouts. Qualifications Required Qualifications • High School Diploma, GED, or ability to demonstrate basic literacy and math proficiency through education, experience, or assessment, • Fluent in English, • Basic computer skills, • Possess math skills and mechanical aptitude., • Must have the ability to learn to use and read micrometers, tape measures, feeler gauges, and basic hand tools., • Must be able to stand/walk on concrete floors for 10-12-hour shifts., • Must be able to push/pull, and lift up to 50 lbs., • Must be able to work in extreme environmental conditions with temperatures ranging from 40-100+ degrees Fahrenheit. Preferred Qualifications • One to two years of experience in a manufacturing environment., • Must be able to be certified as a forklift Operator., • Must be able to be certified as a Certified Welder. Materials and Equipment Directly Used • Strand and Wire rope of various diameters and lengths, on reels or in coils, empty or unassembled reels, paper lagging strips, tags, seizing wire, blocking, thimbles., • Rewinding machines, stanchions, shafts, collars, bushings, rope cutters, measuring devise, fork trucks, banding equipment, welders, various hand tools., • Personal protective equipment, including safety glasses, hearing protection, gloves, and steel-toed safety shoes. Additional Information • Must be legally authorized to work in the United States without restriction., • Employment is contingent upon successfully completing a post-offer background check., • An applicant must complete a satisfactory background check post-offer of employment. A criminal conviction will not be an automatic bar to employment., • Must be willing and able to pass a post-offer drug screen and physical (if required), • Must be 18 years of age or older., • Equal Opportunity Employer/Veterans/Disability

Job DescriptionDock ForemanJob Summary Core Group Resources is hiring an experienced Dock Foreman for night shift at a marine repair shipyard in Charleston, MO. You'll lead a crew of welder/fitters repairing towboats and barges. This role suits a hands-on leader who knows boat and barge repair inside and out and can keep a night crew safe, productive, and on schedule. Responsibilities • Lead and assign work to night shift welder/fitters and dock crew, • Assess hull, deck, and structural damage on barges and towboats and plan repairs, • Read drawings and repair specs and lay out steel replacement work, • Check fit-up and weld quality and sign off on completed repairs, • Run the yard crane when needed to move steel and equipment, • Enforce hot-work, confined-space, and general yard safety procedures, • Coordinate shift handoff with day shift supervisionRequirements, • Marine repair experience with a working knowledge of how to repair boats and barges, • Prior lead or foreman experience in a shipyard or marine fabrication setting, • Strong welding and fitting background, • Able to read blueprints and repair specifications, • Willing to work night shiftPreferred Requirements, • Crane operation experience, • Inland river shipyard experience, • OSHA 10 or 30\nCompany Description Core Group Resources is the bridge that connects the maritime, marine offshore, oil & gas, petrochemical, and environmental industries. Our in depth knowledge of these fields can help you navigate these quickly expanding markets. Core Group is actively assisting companies hiring top-notch marine engineers, operations, and commercial candidates with our expertise in these industries. Candidates seeking navigation into these industries, let us chart your career here. We have mapped out all verticals in this space and know where professionals are best poised for rapid career growth. With strong projected growth in these sectors, now is the time to partner with the leading Houston-based recruitment firm of Core Group Resources. We Offer: Direct Hire, Executive Search, Contract Recruitment, and Recruitment Process Outsourcing Contact us today to learn more about how we can partner with you. Email info@coregroupresources.com to get started. Core Group Resources is the bridge that connects the maritime, marine offshore, oil & gas, petrochemical, and environmental industries. Our in depth knowledge of these fields can help you navigate these quickly expanding markets. \r\n\r\nCore Group is actively assisting companies hiring top-notch marine engineers, operations, and commercial candidates with our expertise in these industries. Candidates seeking navigation into these industries, let us chart your career here. We have mapped out all verticals in this space and know where professionals are best poised for rapid career growth. \r\n\r\nWith strong projected growth in these sectors, now is the time to partner with the leading Houston-based recruitment firm of Core Group Resources. \r\n\r\nWe Offer:\r\n \r\nDirect Hire, Executive Search, Contract Recruitment, and Recruitment Process Outsourcing\r\n\r\nContact us today to learn more about how we can partner with you. Email info@coregroupresources.com to get started.

Job DescriptionMulti-Craft Industrial Maintenance Technician (CNC/PLC) Location: Sedalia, MO — Gardner Denver, 305 N State Fair Blvd, Sedalia, MO 65301 Schedule: 2nd Shift, Monday–Friday, 3:00 PM – 11:30 PM About the Work You’ll Champion At Gardner Denver — Industrial Technology and Services, LLC (an Ingersoll Rand business), we transform castings and raw materials into world-class blowers and compressors for industrial, commercial, and government customers. Our engineers design to exacting standards, and our skilled teams bring those designs to life. You’ll be central to keeping our facility safe, reliable, and running at peak performance. A Day in Your Role • Diagnose and execute complex electrical, mechanical, and construction repairs, interpreting schematics and blueprints to guide your work., • Isolate drive-related faults to the component level across Fanuc, Siemens, Allen‑Bradley, and similar control platforms., • Identify root causes, recommend preventive actions, and document findings and fixes through our work order history., • Keep internal stakeholders informed on equipment status and timelines; coordinate with outside service providers when needed., • Draft sketches for mechanical/electrical alterations or new installations; prepare bills of material and initiate purchase requisitions for larger jobs., • Exercise sound judgment on day-to-day decisions to minimize downtime and enhance safety., • Operate hoists, carts, lifts, fork trucks, and hand trucks to safely move light to heavy materials., • Install, troubleshoot, repair, and maintain CNC machinery; plant electrical systems; and pneumatic/hydraulic equipment., • Reassemble equipment after service; inspect and test damaged parts, tagging defects and advising supervision as required., • Perform lubrication and apply adhesives and other materials to machinery per procedures., • Team up with peers to repair or relocate machines, subassemblies, or components., • Work confidently on high-voltage systems up to 480 VAC, 3‑phase., • Repair or replace linings and components (metal, wood, leather, glass) in machines and equipment compartments.What You Bring, • 2+ years of hands-on experience in manufacturing maintenance., • Multi-discipline troubleshooting ability across pneumatics, hydraulics, electrical and electronic systems, CNC machines, and controls., • Comfort working from concepts when detailed drawings/specs aren’t available; strong blueprint/schematic interpretation skills., • Ability to maintain technical documentation for equipment and processes., • Experience maintaining machine tools: lathes, grinders, mills, drills, machining centers, and related equipment., • Team-first mindset and clear communication.Physical Capabilities, • Stand and walk for up to 8 hours per shift., • Lift up to 35 lbs. independently and up to 70 lbs. with assistance; push/pull up to 35 lbs., • Vision corrected to no worse than 20/35 with glasses/contacts.Preferred, • High School Diploma or GED., • 3+ years specifically focused on CNC machine maintenance.Work Setting On-site at our Sedalia, MO facility; no travel anticipated. Benefits that Back You We embrace a culture of personal ownership at Ingersoll Rand. Expect comprehensive medical and prescription coverage, dental and vision, wellness programs, life insurance, a strong 401(k), paid time off, and an employee stock grant—resources designed to support your health and well-being at work and at home. You’re Skilled In • PLC Troubleshooting Skills, • Equipment Troubleshooting, • Facilities Maintenance Experience, • Electrical Troubleshooting Skills, • CNC Tooling, • Troubleshooting Skills, • Machine Building/Assembling, • Mechanical Troubleshooting Skills, • Troubleshooting Industrial Automation Equipment, • Machine Safety Inspections, • Machine Setups for Production Runs, • Troubleshooting CNC Machines, • Tool/Die/Mold Repair Skills, • Excellent Communication Skills, • Experience in a Manufacturing Environment, • Blueprint ReadingMachines & Technologies You’ll Touch, • CNC Mill (3-4 axis VMC), • CNC Laser Cutter, • CNC Lathe (2-4 axis), • CNC Router, • CNC Swiss Lathe, • Boring Mill, • CNC Grinder, • CNC Plasma Cutter, • Manual Vertical Mill, • Robotic Welder, • Coordinate Measuring Machine (CMM), • Blow Molding Machine, • CNC Mill (5+ axis VMC), • CNC Lathe (5+ axis), • Programmable Logic Controller (PLC), • Conveyor Systems, • Industrial RobotEqual Opportunity We are an equal opportunity employer. All qualified applicants will receive consideration for employment without regard to age, ancestry, color, family or medical care leave, gender identity or expression, genetic information, marital status, medical condition, national origin, physical or mental disability, political affiliation, protected veteran status, race, religion, sex (including pregnancy), sexual orientation, or any other characteristic protected by applicable laws, regulations, and ordinances.

Job Description Maintenance Technician Cape Girardeau, MO How can you make a difference at your job and can have the opportunity to grow? Join the Cape Girardeau– Spartech Team! We are currently looking for a Maintenance Technician to join our team to support our machine maintenance and variety of customers. If you meet the qualifications and want to make a difference in a fast-paced environment with a company large enough to offer you room to grow but not so large you become “just a number”, and who has a large focus on safety and success, Spartech might be the ideal company for you! Job Summary The Maintenance Technician is responsible for safely completing maintenance assignments to build, repair and/or maintain all equipment in good operating condition as quickly and accurately as possible; while keeping associated costs to a minimum to help meet Plant goals. The Maintenance Technician is expected to be multi-skilled and able to contribute to plant maintenance activities in a variety of craft disciplines. This position reports to the Cape Girardeau, MO Maintenance Manager. Essential Duties & Responsibilities • Completes projects with minimal guidance showing a proactive attitude to minimizing equipment down time and lost production capability., • Troubleshoots mechanical devices in operation. Dismantles and examines devices to gain access to and remove defective parts. Adjusts, repairs or replaces defective parts., • Sets up and operates shop machinery such as drill press, grinders, band saws, cutting torch, welder. etc. Uses hand tools and pneumatic tools to modify or repair parts and equipment., • Installs new or repairs/modifies electronic, hydraulic and pneumatic equipment as needed., • Improves reliability and up-time of all equipment. Takes a proactive approach to equipment issues with a preventive maintenance mentality., • Operates forklift and aerial lift platform as needed., • Researches supplies, parts and tools needed to efficiently complete work orders., • Assists in identifying and maintaining an accurate inventory of parts by effective utilization of a CMMS., • Contributes to upkeep and updating of required paperwork such as records, maintenance logs, documents, manuals, drawings, PM logs, etc., • Supports the vision, mission and guiding principles of the company., • Follows applicable Safety, Health and Environmental rules and guidelines while performing job duties., • Maintains departmental housekeeping standards., • Other duties as assigned. Requirements Required Education and Skills: • Must have a high school diploma or equivalent., • Must have basic skills on use of computers: MS Office, Windows, SAP is desirable., • Requires the ability to safely operate a wide variety of tools such as hand tools, power tools, drill press, band saw, welder, cutting torch, etc., • Must have knowledge of mechanical systems including gear boxes, motors, air compressors, pumps, AC, DC, drive troubleshooting, etc., • Must be able to navigate electrical, hydraulic, and pneumatic schematics and blueprints for planning and troubleshooting., • Must be able to read, communicate and comprehend written and oral instructions in English; read and comprehend safety rules, operating and maintenance instructions, procedure manuals, equipment files, etc., • Ability to communicate effectively in writing form through letters and email. Ability to do research on the Internet or company Intranet., • Ability to implement, enforce and maintain guidelines set by the Company or management., • Ability to handle multiple tasks in a fast-paced environment. Strong organization skills and self-starter motivation. Prioritization skills in alignment with Plant priorities. Continuous Improvement mindset and results oriented., • Must have math skills to add, subtract, multiply and divide and the ability to perform these operations using units of weight measurement, volume, and distance. Ability to apply principles of logical or scientific thinking to a wide range of intellectual and practical problems. Ability to deal with nonverbal symbolism (formulas, scientific equations, graphs, etc.), • Must have ability to reason and address problems involving a few concrete variables in standardized situations., • Must have manual dexterity sufficient to operate a wide variety of hand tools, hand trucks, forklift, mechanical platforms and lifts, bench tools, welders, saws, drills etc., • Strong Industrial Electrical experience including troubleshoot and repair PLC's, electronics experience, DC drive units, programmable logic, working with 3 phase motors, 480v and below, MA current signals. Years of Experience: • 5 years of prior experience in industrial maintenance, electrical, mechanical, or in a related field; or a combination of education and experience deemed equivalent Required Certification, Licenses, Registration: • Specific Craft Certification/Licenses a plus, • Technical education a plus Benefits We offer competitive salary, incentive and benefit programs. Benefits include: medical, dental, vision, company paid life and long-term and short-term disability programs plus flexible spending accounts and a strong 401(k) matching program. In addition, we offer a generous Vacation program. Spartech LLC, headquartered in Maryland Heights, Missouri is a leading manufacturing organization in the Custom Sheet & Roll Stock and Packaging industries with numerous locations throughout the United States. We have a broad customer base with extensive product offerings. Many of our materials are used in products you might see every day— for example if you start your morning with a yogurt or your child eats a single serving peanut butter—you may have already seen some of our materials. More unique uses of our materials can be seen in Military or security applications, for example, with bullet proof materials. From routine daily-life to life-saving applications—we make a difference. Our broad scope of products and services keep our environment interesting and challenging with a culture focused on success. NOTE: Spartech, LLC provides equal employment opportunity to all qualified applicants regardless of race, color, religion, national origin, sex, sexual orientation, gender identity, age, disability, genetic information, or veteran status, or other legally protected classification in the state in which a person is seeking employment. Spartech will use E-Verify to ensure employment eligibility of newly hired employees where required.

Job Description Laser Welder (YAG / TIG) – 1st Shift Location: Grand Rapids, MO Pay: Competitive — based on experience About Phoenix Laser Solutions Phoenix Laser Solutions is the largest YAG laser weld house in North America, with five Midwest locations. We specialize in precision laser welding, TIG welding, and cladding for industries including aerospace, medical, and injection molding. We repair and enhance high-value components using advanced welding technology that goes beyond traditional methods. Position Overview We are hiring a Laser Welder / TIG Welder for our Grand Rapids facility. This role involves precision welding, blueprint interpretation, and working with a variety of metals and components in a clean, climate-controlled environment. Key Responsibilities • Perform laser welding (YAG) and/or TIG welding on precision components, • Select appropriate weld materials, filler metals, and processes, • Prepare parts by grinding, cleaning, and setup, • Read and interpret blueprints, drawings, and technical instructions, • Measure and document dimensions and tolerances, • Inspect finished work to ensure quality standards are met, • Identify best welding methods for each job, • Support continuous improvement in processes and workflow Qualifications • Experience with laser welding, TIG welding, or similar precision welding processes, • Ability to read and understand technical drawings and blueprints, • Strong attention to detail and quality, • Ability to work independently with minimal supervision, • Problem-solving mindset and adaptability, • Prior experience in tooling, mold repair, aerospace, or medical components is a plus Physical Requirements • Lift up to 50 lbs, • Sit for extended periods, • Perform repetitive tasks, • Pass vision screening, • Overtime available as needed Compensation & Benefits • Pay commensurate with experience and skill level, • Health, Dental, and Vision Insurance, • Simple IRA with up to 3% employer match, • Paid Time Off (PTO), • Annual performance reviews with raise opportunities, • Clean, climate-controlled work environment Why Join Phoenix Laser • Work on high-precision, non-production welding projects, • Advanced equipment and technology, • Stable company with long-term growth, • Opportunities for advancement Learn more: www.phoenixlaser.com

Position Title: Operations Manager Salary: $85,000-$110,000/year An Operations Manager opportunity in Springfield, MO is available through Accelerate Professional Talent Solutions. Operations Manager Responsibilities include but are not limited to: Estimating • As assigned, provide research, cost basis and analysis to support operational objectives, • Assist and provide support to estimating on means, methods, sequences, schedule, material breakdowns, rentals and field hours, • Assist in labor hour take-offs, equipment sizing, safety processes and pre-bid quotations for specialty fabricated items Sales • As assigned participate on Pre-bid job site visits, • Review pre-bid or pre-contract job site safety requirements, • Travel and assist Sales with operational support when closing contracts, • Travel and assist Sales when faced with imposing customers, • Understand the customers and how the teams can foster a professional relationship, • Mentor the site supervisors in customer, subcontractor, and vender relationships Tool Depot • Support research and development of safe work tools and equipment, • Provide planning, logistics, processes, and communication efforts to support Operational Objectives, • Develop job specific tool lists and understand the cost associated with them, • Develop internal and external material logistic plans, • Develop and oversee execution of tool, material and equipment loads to job site, • Communicate tools and equipment deficiencies and gather data to support capital purchase to support the business, • Lead field crews through tool repair, maintenance, tagging and reporting, • Develop and enforce tools and equipment treatment and accountability to the field crews, • Analyze buy lists with tool depot to develop alternative methods when capacity is driving costs on buy lists Safety • Directly integrated into the Adaptive Safety Program and responsible for teaching, enforcement, and discipline, • Review site conditions prior to mobilization to develop a safe work plan and communicate to the site crews (confined space, fire/hole watch, elevated work), • Assist in all safety related incidents, accidents, root cause, near miss, discipline or otherwise safety reporting, • Collaborate with Safety Manager and/or Safety Consultants to provide safe works solutions for new or undefined conditions; support Safety Manager with corrective measures to Safety Objectives, • Ensure all employees have current and appropriate training for operations they intend to perform, • Be an objective and decisive stakeholder in all aspects of safe work, corrective measures, discipline, and workplace culture Operations • Develop both short- and long-term project specific schedules, • Develop project specific means/methods, sequence of erection, lift plans and shipping plans, • Develop project specific labor breakdowns for performance reporting, • Organize and maintain appropriate weld procedures and ensure their crew has the relative welder certifications for the specific job, • Organize appropriate code paperwork, travelers and arrange for inspections for ASME code work, • Dispatch field crews that have the skills to meet the project scope, schedule and estimate, • Teach, mentor and train field supervisors to ensure they have the skills and abilities to be successful, • Direct authority over the field supervisors and their crew; daily calls to stay aligned with progress, schedule, quality and troubleshooting are expected, • Indirect authority over field engineers as assigned by job; have a rapport with Field Engineers to work as a team with field crews, • Support QA/QC in developing, executing quality plans and testing plans for field projects, • Develop and organize Job Site Layouts & Execution Plans, • Collaborate with Project Management to justify an amended plan with an internal change order, • Work with and carry out Project Management directives related to scope, schedule and costs, • Communicate to both Director & Project Management regarding, safety, progress, critical lifts, customer impacts, subcontractor impacts or otherwise complex issues at the job site, • Site visits as needed to kick-off projects, final completion, critical lifts, behavior, performance, schedule or safety events to ensure a project and crew success, • Engage with and support other departments (procurement, engineering, accounting, payroll) to support project and company objectives, • Provide communications through meeting notes, reminders, calendars to maintain operational objectives and efficiencies, • Proactive and critical thinking to avoid operational impacts; study, analyze and ‘play out’ operational milestones to predict operational challenges; inform the team to collaborate and overcome Engineering • Understand the exposure to engineering changes and modifications executed in the field; work with ADAPTIVE Engineering or 3rd parties to formally resolve to mitigate risk, • Be proactive and diligent to engage Engineering to support the success of projects Business/Management • Participate in GGOB weekly huddles and present information as assigned, • Collaborate with Project Managers (monthly) on Job Analysis Process for P&L Management, • Participate in business planning efforts as it relates to the safety program, tools, equipment, • Enforce and discipline company policies and procedures, • Travel with short notice, short term – approximately 0-40% Qualifications for Operations Manager: • Must be a team player willing to guide the members to work together as well as work with all employees in the company to provide the most accurate and timely information for external and internal customers, • Must have excellent verbal, communication, and negotiating skills, • Must have strong technical skills and ability to adapt, • Must have applicable computer skills with knowledge of Windows, Microsoft Word, AutoCAD, Excel, and Microsoft Project, must be willing to improve computer skills as needed, • Must be flexible and willing to learn new duties as they arise and recognize the need for additional effort to reach an objective, • Must be available to our customers on an extended basis as related to emergencies of safety, • Must be able to work in a high-pressure environment while still producing accurate work, • Must provide the people skills to work with many different personalities in a positive, collaborative and productive manner., • Must provide a positive company attitude, • 6-10 years of stainless steel fabrication, industrial construction experience and 3-5 years of labor management, • Must be able to read documents and computer screen, • Must be able to communicate with team members and management and listen to equipment, • Must be able to move about the production or job site areas by stepping over and/or bending under objects; and the ability to stand up to 1 hour, • Must be able to stoop or kneel to pick up items from the floor, • Must be able to lift 30 pounds with or without reasonable assistance, • Must be able to grasp and use equipment and tools

Job Description D7 Pneumatics LLC is seeking a motivated and dependable Industrial Maintenance Technician to join our growing team. This position involves working at a variety of industrial facilities, including sawmills, steel mills, concrete plants, manufacturing facilities, and other industrial operations. The successful candidate will be responsible for installing, maintaining, troubleshooting, and repairing industrial equipment while providing safe, high-quality workmanship. This is a hands-on field position requiring mechanical aptitude, problem-solving skills, and the ability to work independently and as part of a team. Responsibilities • Perform maintenance, repairs, and troubleshooting on industrial equipment and systems., • Install, service, and repair pneumatic, hydraulic, and mechanical equipment., • Diagnose equipment failures and determine corrective actions., • Conduct preventative maintenance inspections and repairs., • Read and interpret blueprints, schematics, and technical drawings., • Work safely in active industrial environments including sawmills, steel mills, concrete plants, and manufacturing facilities., • Complete required documentation and maintenance reports., • Communicate effectively with customers, supervisors, and coworkers., • Travel to various job sites as required.Qualifications, • Experience in industrial maintenance, millwright work, mechanical maintenance, or a related trade preferred., • Strong mechanical aptitude and troubleshooting abilities., • Ability to work safely in industrial environments., • Experience with pneumatic, hydraulic, and rotating equipment is an asset., • Ability to work independently with minimal supervision., • Strong work ethic and positive attitude., • Valid driver's license and reliable transportation., • Ability to lift up to 50 lbs and perform physically demanding work.Required Tools Candidates are expected to provide and maintain their own personal hand tools, including but not limited to: • Impact gun(s), • Socket sets, • Combination wrench sets, • Adjustable wrenches, • Pliers and specialty hand tools, • Tape measure, • Allen/Hex key sets, • Basic diagnostic and troubleshooting toolsTravel Requirements, • Travel may be required depending on project and customer needs., • Occasional overnight stays may be necessary., • Per diem and travel accommodations will be provided when applicable.Preferred Certifications (Not Required), • OSHA 10 or OSHA 30, • MSHA Certification, • Forklift Certification, • Aerial Lift Certification, • First Aid/CPR, • Millwright, Pipefitter, Welder, or related trade experienceWhat We Offer, • Competitive pay based on experience, • Overtime opportunities, • Career advancement opportunities, • Exposure to a wide variety of industrial facilities and equipment, • Supportive team environment, • Training and development opportunities

Job Description Position Overview We are seeking an experienced Director of Quality to provide strategic and operational leadership for quality assurance and quality control within a heavy industrial manufacturing environment. This position will oversee the Quality Management System, inspection, supplier quality, welding quality, NDE/NDT, material traceability, nonconformance management, audits, and continuous improvement. The ideal candidate has significant quality leadership experience within pressure vessels, heat exchangers, boilers, power generation equipment, heavy fabrication, or similar engineered-to-order manufacturing. Key Responsibilities • Lead the overall Quality Assurance and Quality Control organization., • Maintain and continuously improve the Quality Management System., • Ensure compliance with applicable ISO, ASME, customer, and regulatory requirements., • Develop and maintain quality procedures, inspection plans, standards, and documentation., • Oversee inspection and testing throughout fabrication, assembly, and final product acceptance., • Ensure complete material traceability and proper retention of quality records., • Oversee welding quality, weld procedures, welder qualifications, and associated documentation., • Provide leadership for NDE/NDT activities including UT, PT, MT, PAUT, and other applicable methods., • Oversee hydrostatic, pneumatic, dimensional, and final inspection activities., • Lead internal, customer, supplier, and third-party quality audits., • Manage nonconformances, root cause investigations, corrective actions, and preventive actions., • Monitor quality KPIs including defects, rework, scrap, customer complaints, supplier performance, and corrective actions., • Work closely with Engineering, Manufacturing, Project Management, Supply Chain, and Operations to resolve quality issues., • Develop and maintain supplier quality standards and evaluate supplier performance., • Support customer quality requirements, inspections, documentation, and technical reviews., • Drive continuous improvement initiatives to reduce defects, rework, and manufacturing quality costs., • Develop, mentor, and lead Quality Engineers, Inspectors, NDE personnel, and other quality team members., • Promote a strong culture of accountability where quality is integrated throughout the manufacturing process.Qualifications, • 10+ years of progressive Quality Assurance/Quality Control experience within heavy industrial manufacturing., • 5+ years of quality leadership or management experience., • Strong experience with ASME Code manufacturing and ISO 9001 quality systems., • Experience with pressure vessels, heat exchangers, boilers, piping, or other large fabricated equipment strongly preferred., • Strong knowledge of welding, fabrication, inspection, NDE/NDT, and material traceability., • Experience managing nonconformances, CAPA, root cause analysis, and continuous improvement., • Experience leading internal, customer, supplier, and third-party audits., • Strong understanding of manufacturing drawings, specifications, codes, and customer quality requirements., • Proven ability to lead and develop Quality Engineering and Inspection teams., • Strong leadership, communication, analytical, and problem-solving skills.Preferred Qualifications, • Bachelor's degree in Engineering, Quality, Manufacturing, or a related technical field., • Experience within power generation, nuclear, energy, petrochemical, process equipment, or similar industries., • Experience with ASME Section I, Section III, and/or Section VIII requirements., • Familiarity with National Board requirements and code stamps., • Experience with nuclear quality requirements such as NQA-1 and 10 CFR 50 Appendix B is a plus., • ASQ certifications such as CQE or CQM/OE are a plus., • Lean Manufacturing or Six Sigma certification preferred., • Experience managing supplier quality across domestic and international manufacturing partners.

Job DescriptionCDR General Services is seeking experienced and dependable Stick Welders for a full-time opportunity in Hartford, IL. This position requires strong SMAW welding skills using 6011 and 7018 electrodes, with the ability to successfully complete welding tests in multiple positions. Candidates should be safety-conscious, reliable, and comfortable working in an industrial environment. Job Details • Location: Hartford, IL, • Job Type: Full-Time, • Pay: 24.00–27.00 per hour Requirements • Previous professional Stick/SMAW welding experience required., • Must have experience welding with 6011 and 7018 electrodes., • Must be able to complete approximately a 12-inch weld test in the following positions:, • Horizontal Butt, • Vertical Lap, • Vertical Butt, • Overhead Lap, • Overhead Butt, • Must understand proper bevel preparation and root-pass techniques using 6011 electrodes., • Must understand proper storage and handling of 7018 electrodes to prevent moisture contamination and weld defects., • Must be familiar with appropriate amperage settings for 6011 and 7018 welding rods., • Must be able to perform vertical-uphill welding using proper technique., • Must understand common welding defects, including slag inclusion, porosity, undercut, and hydrogen cracking., • Must be available to work Monday through Saturday and approximately 48 hours per week., • Must be able to work the assigned shift. Qualifications • Strong knowledge of SMAW/Stick welding procedures., • Experience performing structural or industrial welding preferred., • Ability to produce quality welds in horizontal, vertical, and overhead positions., • Knowledge of proper electrode handling, weld preparation, and cleaning between passes., • Ability to identify and prevent common welding defects., • Strong attention to safety, quality, and productivity., • Dependable attendance and ability to work effectively in a fast-paced industrial environment.

Job DescriptionJob Description Who will you be working with: You will work closely with production employees, welders, supervisors, quality, engineering, safety, maintenance, and other production support teams. The Welder III serves as a technical resource within the production environment, supporting welding operations, complex repairs, training efforts, and continuous improvement initiatives while partnering closely with leadership to ensure safe, efficient, and high-quality operations. How will you make a difference: The Welder III is a highly skilled trades position responsible for performing complex welding operations, weld build-up repairs, and critical welding applications associated with the remanufacturing and repair of locomotive components. This role requires advanced knowledge of multiple welding processes, the ability to interpret technical drawings and welding procedures, and expertise in producing high-quality welds that meet company and customer specifications. The Welder III plays a key role in supporting safety, quality, productivity, and operational excellence by performing advanced welding tasks, identifying and correcting weld defects, supporting less experienced welders, and contributing to efficient production processes. This position helps ensure components are repaired and manufactured to the highest standards while supporting business objectives and customer expectations. Monday - Thursday 5:00am - 3:30pm. This position might require flexibility to work overtime on Fridays and Saturdays. 4800 Deramus Ave, Kansas City, MO 64120 What do we want to know about you? • Preferred Associate Degree (A.A.) or equivalent from a trade school with technical training in welding., • Minimum five (5) years of welding experience for external candidates., • Minimum two (2) years of welding experience for internal candidates who have successfully completed Level I and Level II Wabtec welding training., • Must complete all local Welder I and Welder II training and qualification requirements., • Ability to effectively communicate, read, and understand welding procedures, technical drawings, work instructions, and business communications in English., • Ability to work independently with limited supervision while maintaining safety, quality, and productivity expectations., • undefined Knowledge and Skills • Advanced knowledge of MIG, TIG, Stick, Flux-Core, and other applicable welding processes.Ability to read and interpret blueprints, schematics, welding symbols, and Welding Procedure Specifications (WPS)., • Strong understanding of metal properties and the effects of heat and welding processes on materials., • Proficiency with grinders, cutting torches, plasma cutters, and other fabrication tools., • Strong measurement and precision skills, including the use of calipers, micrometers, and other measuring devices., • Ability to identify weld defects such as cracks, porosity, undercut, lack of fusion, inclusions, and burn-through.Ability to pass applicable welder qualification tests in accordance with AWS D15.1 requirements., • Ability to train, coach, and provide technical guidance to less experienced welders., • Willingness to cross-train and support other production areas as business needs require. What will your typical day look like? • Perform advanced welding operations on large and complex components using approved welding procedures and specifications., • Plan welding sequences and regulate heat, feed, current, voltage, electrodes, and other welding parameters to achieve proper penetration, fusion, and weld quality., • Perform weld build-up repairs, high-pressure welding, code welding, and other critical welding applications requiring a high degree of skill and precision., • Read and interpret blueprints, technical drawings, welding symbols, and work instructions to ensure compliance with specifications and tolerances., • Align, fit, and weld components while minimizing distortion and maintaining dimensional accuracy., • Perform air carbon arc gouging to remove defective welds and prepare materials for repair and rework., • Inspect completed welds and identify defects requiring corrective action., • Support production goals by maintaining quality standards, productivity expectations, and workflow requirements., • Assist in training, mentoring, and providing technical guidance to lower-level welders., • Follow all safety procedures, PPE requirements, and quality standards while maintaining a clean and organized work area., • Participate in cross-training activities and support operational needs across production areas when required., • Perform other duties as assigned. What about the physical demand of the job: Physical Demands: (The physical demands described here are representative of those that must be met by an employee to successfully perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.) • Regularly lift, move, carry, push, and/or pull materials, components, and equipment weighing up to 50 pounds., • Walk throughout the production facility and remain on your feet for extended periods, including the duration of a full shift., • Perform welding, grinding, fitting, and fabrication activities in a manufacturing environment., • Frequently bend, kneel, twist, reach, climb, crouch, and work in confined or difficult-to-access areas., • Use hand tools, welding equipment, measuring instruments, and material handling equipment as required., • Maintain the visual acuity necessary to inspect weld quality, read technical drawings, identify defects, and safely perform welding activities., • Maintain regular on-site attendance and presence during scheduled shifts to support production operations and business needs. Work Environment: (The work environment characteristics described here are representative of those an employee encounters while performing the essential functions of this job.) • Work is performed in shop environment that is non-temperature-controlled production environment, with exposure to varying temperatures, noise and other environmental factors. Additional Information Our job titles may span more than one career level. The salary rate for this role is currently $30.50. The actual salary offered to a candidate may be influenced by a variety of factors, such as: training, transferable skills, work experience, education, business needs, market demands and work location. The base pay range is subject to change and may be modified in the future. More information on offered benefits, which include health, welfare, and retirement, are available at mywabtecbenefits.com. Other benefit offerings for this role may include annual bonus, if eligible. What could you accomplish in a place that puts People First? At Wabtec, it’s not just about a job - it’s about the impact you make. When our people come together, we’re Expanding the Possible by continuously improving what we do and how we do it - for our clients and each other. If you’re ready to revolutionize how the world moves for future generations, Wabtec is the place for you. Who are we? Wabtec is a leading global provider of equipment, systems, digital solutions, and value-added services for the freight and transit rail sectors. Drawing on more than 150 years of experience, we are leading the way in safety, efficiency, reliability, innovation, and productivity. Whether it’s freight, transit, ports, logistics, mining, industrial, or marine, our expertise, technologies, and people together – are accelerating the future of transportation. With roots that date back to George Westinghouse, Thomas Edison, and Louis Faiveley, Wabtec has always built technologies and implemented solutions for a variety of sectors that are critical to meeting the needs of customers and governments alike. Our global team of about 30,000 employees worldwide delivers performance that moves the world forward. We’re lifelong learners, obsessed with better. Learn more at www.WabtecCorp.com. Culture powers us and the possibilities. We believe the best ideas come from a mix of experiences and backgrounds. At Wabtec, we strive every day to create a place where everyone belongs. We’re building a culture where leadership, inclusion and your unique perspective fuel progress. We’re proud to be an Equal Opportunity Employer. We welcome talent of all backgrounds, experiences, and identities, including race, gender, age, disability, veteran status and more. Need accommodation? Just let us know - we’ve got you.

Job DescriptionJob Location: Milwaukee, WI Compensation: $22/hour — 30-day performance review with opportunity to increase to $24/hour Shift: 1st or 2nd shift Hours: Up to 60 hours/week; additional OT may be available with supervisor approval Per Diem: $100/day on days worked Key Responsibilities • Perform MIG welding on heavy-gauge steel components, fuel tanks, frames, and enclosures., • Weld in flat, vertical, and overhead positions., • Read and follow blueprints and measurements., • Clamp, position, tack, grind, and assemble components., • Inspect finished work and troubleshoot basic issues., • Follow safety and quality standards.Qualifications, • MIG/GMAW welding experience preferred., • Must be able to read blueprints and a tape measure., • Strong attention to detail and willingness to learn., • Reliable and able to work well with a team., • Must be willing to work 1st or 2nd shift and overtimeRequirements, • Pass background check and 5-panel drug test., • Pass pre-employment physical., • Pass written test and basic weld test on first day. #wideeffect

Job Description HIRING IMMEDIATELY! PAID EVERY FRIDAY FOR YOUR TIME SAME WEEK! At Doing Steel, we are a weekly pay structural steel get it done place! If you're looking for a steady work place with 50 hour weeks paid every Friday, and if you are hard working with welding/fitting experience- we want to talk to you! Company Overview Doing Steel Fabrication, LLC has a proud history of delivering top-quality steel fabrication services since 1986. With extensive facilities and a dedicated team, we serve projects across the country, emphasizing excellence and innovation in our industry. Doing Steel is a family-owned company who believe in our people. We support our people through a strong benefits package, including 401K with match, and weekly pay. JOB DESCRIPTION & DUTIES · OPERATING A TAPE MEASURE · MATHEMATICAL UNDERSTANDING · CLEANS UP MATERIAL BY GRINDING OR CHIPPING. · SPOTS PAINTS FOR IDENTIFICATION MARKS · OPERATION OF HAND TOOLS · MACHINE OPERATION · WELDING · FITTING ESSENTIAL FUNCTIONS: • Maintains a clean work environment., • Ability to work in a team environment and independently, • Collaborate with warehouse, production, and logistics teams to ensure efficient, safe loading and unloading operations., • Ensure safe, timely loading and unloading processes., • Able to stand and work on concrete floor for 10-hour shifts, • Ability to see, hear, and interact verbally with co-workers, • Ability to use computer screen to enter time and job data using fingers, • Ability to reach, bend, and lean to access materials being welded and fitted., • Ability to lift 25lbs routinely Education and Experience: • High school diploma or GED equivalent preferred., • Experience with trucks under three tons (i.e. tractors and fork-trucks), mobile crane equipment and overhead cranes., • 2 years experience in manufacturing environment preferred., • Welding Certificate, • 2 years MIG welding experience preferred Schedule: • 10-hour shift, • Day shift or 2nd shift, • Monday to Friday WORK ENVIRONMENT: Exposure to dust, fumes, noise and high-degree varying seasonal temperatures. Machinery with energy sources including electrical, mechanical, hydraulic, pneumatic, chemical, or other energy. PHYSICAL DEMANDS: The physical demands described here are representative of those that must be met by an employee to successfully perform the essential function of this job. While performing the duties of this position, the employee is regularly required to walk, stand, use hands and fingers, handle, grasp or feel; reach with hands and arms climb or balance; stoop, kneel, crouch or crawl. Additional requirements consist of, but are not limited to, lifting, pushing and pulling material, stairs, and ladders. When there is an occasion to move heavy material greater than 50 pounds, the operator will request assistance from another team member or utilize provided lifting equipment. Doing Steel is an Equal Opportunity Employer. All positions at Doing Steel require a pre-employment drug screen; all job offers are contingent upon the successful completion of the drug screen. Failure to pass a drug screen prior to employment or at any time during employment will result in the recension of the offer and/or termination of employment. Doing Steel is a Drug-Free Safety-First workplace. All applicants must successfully complete a drug screen prior to being hired. Failure to submit to or pass a drug screen will result in any offer of employment being rescinded. Failure to submit or pass a drug screen, at any time while employed by Doing Steel, or any of its subsidiaries, will result in termination of employment. Drug screens may be given at any time to any employee for reasonable suspicion, or as part of a random selection, or post-accident or incident.

Job Description JUMPSTART, ADVANCE, AND LOVE YOUR CAREER WITH SMSI! At SMSI, we believe in our employees. With above-average pay, extensive benefits, vocational training, and a family-based atmosphere, we are always looking for people seeking to improve themselves. Together, our team strives to perform the best service possible for customers. We thrive on challenges and believe in fair compensation for dedication, detail, and professionalism. Apply today! We are seeking an Industrial / Sanitary Welder to join our team! Benefits: Medical Dental Vision 401(k) Life Insurance Paid Time Off Compensation will be determined based on the candidate's experience and qualifications. Compensation: $30 - $31 hourly Responsibilities: Produce and create finished metal goods. Set up and fix a variety of machinery and parts. Adhere to the blueprints in order to fulfill the product specifications. Determine material dimensions to confirm requirements. Arrange the necessary parts for welding in accordance with the provided specifications, such as using powered saws to cut materials to the required measurements. Perform examinations to assess the quality and tolerance of welds. Ensure that the equipment is kept in a state that does not jeopardize safety. This position is safety-sensitive. Qualifications: Prior experience in welding, manufacturing, or a related field. Crew lead experience is highly preferred. Must be available to travel and able to work weekends when needed to meet customer standards. Strong knowledge of welding equipment and techniques. Strong capabilities in interpreting engineering blueprints and schematics. Excellent understanding of various types of metal and their respective properties. Familiarity with safety regulations and readiness to utilize personal protective equipment. Must have a Class E driver's license for use of company vehicles. Ability to work in a high-demand industry. Must be able to work in a multicultural environment. About Company SMSI is dedicated to providing the highest quality mechanical services performed in an honest, dependable, and efficient manner. SMSI offers lots of room to grow in a fast-paced company. We have been serving commercial and industrial markets for 30 years.

Job Description AES Manufacturing is looking for an experienced MIG Welder / Fabricator who can do more than just run a bead. We want someone who can read a print, fit and fabricate parts, solve problems, and take work from raw components to a quality welded assembly. AES builds safety products that help protect workers, so the quality of the weld and the accuracy of the finished assembly both matter. What You Will Do • Perform MIG welding on carbon steel, stainless steel, and other materials used in AES products as required., • Read fabrication drawings, blueprints, weld symbols, work orders, and sketches., • Measure, lay out, fit, tack, weld, grind, and finish fabricated assemblies., • Use fixtures, jigs, saws, grinders, hand tools, and other approved fabrication equipment safely., • Build repeat-production and custom fabricated components., • Inspect your own work for weld quality, fit, dimensions, and overall workmanship., • Troubleshoot fit-up, distortion, sequence, and fabrication problems., • Support robotic welding, fixture work, or other fabrication functions when qualified and needed., • Maintain a clean, safe, organized work area and meet production expectations without sacrificing quality What We Are Looking For • Strong MIG welding and metal fabrication ability., • Ability to read fabrication drawings and blueprints., • Ability to measure accurately, fit assemblies, and work independently after understanding the job., • Consistent weld quality and ownership of the finished product., • Practical problem-solving ability and willingness to accept feedback., • Reliable attendance and safe work habits. Experience That Helps • Two or more years of welding/fabrication experience preferred, or equivalent demonstrated ability., • Custom fabrication and fit-up experience., • TIG welding, stainless steel, fixtures, jigs, or robotic welding experience., • Forklift experience or certification. What AES Offers • Health, dental, and vision insurance., • Additional company-paid and voluntary benefits according to current AES plan terms., • Paid holidays and paid time off., • 401(k) with company match., • Full-time, year-round manufacturing work., • Opportunities to cross-train and grow into higher-skill manufacturing roles. Career Growth Strong welders can progress into advanced fabrication, robotic welding, senior welder/fabricator, training, fixture development, quality, or lead responsibilities based on demonstrated skill and business need. How We Hire Years of experience help, but they are not everything. Qualified candidates will tour AES and complete a practical welding/fabrication skills assessment.

Job Description Summary – Fabricator / Welder: We are seeking an experienced Fabricator / Welder that would be responsible for fabricating and repairing metal by applying appropriate welding techniques to support the production of high quality, small batch products with a well-respected long-standing precision manufacturer in Kansas City. What's in it for you as a Fabricator / Welder: • Exceptional work environment in a temperature friendly plant, • Great shift: 4-10 hours shift Monday-Thursday so you'd have a 3-day weekend, • Friendly, resourceful, competent production supervisors that provide a low-stress environment to bring out the best in you, • Stable, secure company that can provide you with career longevity Responsibility Summary – Fabricator / Welder: • Use manual and CNC controlled saws, lathes, drill press, and grinder to fabricate metal to specifications, • Arc, TIG, and MIG welding, • Read and interpret blueprints and other shop documentation, • Leads or supports prototype fabrication and process development for new or custom products, • Follow safety and quality standards. Qualification Summary – Fabricator / Welder: • Education: High School Diploma or equivalent, • 3-5 years of related welding and fabrication experience, • Proficient in blueprint reading and interpretation, • Advanced knowledge of welding techniques and metalworking practices, including proficiency with multiple welding processes, • Familiarity with ERP systems, lean manufacturing, 5S and continues improvement principles, • Must have good math skills, • Able to safely lift up to 50lbs #HP

Job Description Job Summary Responsible for ensuring Martinrea and Customer quality requirements are met while welding materials into parts. Required Education & Experience · Must have a current AWS certificate · Sound understanding of Welding Metallurgy · Fundamental understanding of NDE techniques · Sound understanding of Gas Metal Arc Welding, Projection and Resistance Welding · Manual GMAW experience · Working experience with industrial robots · Must have good interpersonal and communication skills. · Good problem solving skills · Must be willing to work shifts and be flexible (including overtime on short notice) · Ability to work well with fellow team members and promote "Team" concept · Basic knowledge of ISO/TS 16949:2002 an asset · Basic knowledge and use of measuring equipment · Basic Computer skills · Understanding of Core Skills and basic GD&T · Basic understanding of CMM Essential Functions/Competency Level · Perform all duties and promote them in a manner that reflects the Martinrea Expectations, through Martinrea Employee Charter. · Contribute to continuous improvement and cost reduction activities. · Support the WEC's on new and existing programs · Support Buy offs when required · Keep the product cleaned up in quarantine · Establish, maintain, and implement welding parameters to support production and Quality Assurance · Conducts weld inspection and analyze weld data, generate reports · Assist with Robotic weld touchups · Archiving and maintaining Paxit system · Be dedicated to generating and or assisting in PPAP packages when required · Maintain a sound understanding of customers' product and engineering specifications · Participate in problem solving activities · Participate in Product, System and Process Audits as required · Assist in the training of production personnel in all quality requirements when required · Provide support to all Departments for weld related issues · Abide by all Company policies including, but not limited to Health & Safety, Quality & Environmental Systems, HR policies and Martinrea Employee Handbook Work Environment • Working in a factory environment, • Frequent distractions and interruptions, • Multiple demands in a challenging and fast paced - team orientated environment Physical Demands · Constant standing · Constant communication with employees, peers, management · Possible use of computer and dispatch radio · Overtime as required · Lifting as required Health & Safety Must work in accordance with H&S regulations, Company and plant rules, policies and procedures Must use or wear PPE and certain clothing as required by the Company

Job Description General Summary: • Lays out, fits, and welds fabricated, cast, and forged components to assemble parts or tanks, with assistance from Bay Supervisor or Master Craftsman. This position is classified as a safety sensitive position, see Limitations and Disclaimer for additional information. Essential Job Functions: • Studies engineering drawings and blueprints, locates and marks bending and cutting lines, and lays out and examines metal stock to ensure specifications are met., • Aligns and fits parts, moves parts into position, and secures parts for welding., • Verifies conformance of workpieces to specifications, and prepares completed work to be checked by supervisors., • Sets up and operates fabricating machines and welding equipment., • MIG, TIG, Flux, Core, stick, and tack-welds parts and tank seams., • Completes manufacturing documentation in a timely manner., • Weld up lower level parts, patch holes for grinders and tack parts together., • Will train on some basic grinding as needed., • Follows all safety guidelines as noted in Safety Manual., • Assists all supervisors and performs other duties as needed and directed. Knowledge, Skills, and Abilities: • Needs to be able to pass 0808GT16-2 weld test as well as the 0808GM31-1 (short-arc) and 0808GM33-1 (pulse) processes., • Must be able to use a plasma cutter, cutting torch and cutting wheel., • Knowledge of design techniques, tools, and principles involved in production of precision technical plans, blueprints, drawings, and models., • Knowledge of welding/grinding procedures., • Ability to keep hand and arm steady while moving or holding arm and hand in one position., • Ability to read cut sheets, blueprints, and tape measures, • Ability to keep hand and arm steady when moving or holding arm and hand in one position., • Ability to meet budgeted hours. Education and Experience: • High school diploma or general education degree (GED); or 1-3 years related experience and/or training; or equivalent combination of education and experience. Working Conditions: • While performing the duties of this job, the employee is regularly exposed to moving mechanical parts; fumes or airborne particles and vibration. The employee is occasionally exposed to high, precarious places and toxic or caustic chemicals., • The noise level in the work environment is usually loud., • The employee must frequently lift and/or move up to 25 pounds and occasionally lift and/or move up to 50 pounds. Limitations and Disclaimer: The above job description is meant to describe the general nature and level of work being performed; it is not intended to be construed as an exhaustive list of all responsibilities, duties, and skills required for the position. All job requirements are subject to possible modification to reasonably accommodate individuals with disabilities. Some requirements may exclude individuals who pose a direct threat or significant risk to the health and safety of themselves or other employees. Safety sensitive jobs are those with tasks or duties that reasonably could affect the health and safety of the employee and others. Safety sensitive jobs include, but are not limited to, jobs that use heavy machinery, use power tools, operating public transportation or dealing with hazardous chemicals. Employees hired to safety-sensitive positions must submit to regular drug and alcohol testing, as well as post-accident testing. This job description in no way states or implies that these are the only duties to be performed by the employee occupying this position. Employees will be required to follow any other job-related instructions and to perform other job-related duties requested by their supervisor in compliance with Federal and State Laws. Requirements are representative of minimum levels of knowledge, skills and/or abilities. To perform this job successfully, the employee must possess the abilities or aptitudes to perform each duty proficiently. Continued employment remains on an “at-will” basis.

Job Description Join Henderson Products Inc., located in Columbia, MO! We are the North American leader in the design, manufacture and up fit of multi-purpose equipment for heavy-duty work trucks specializing in snow and ice control and “Keeping America’s Roads Safe!” Day Shift Hours! Monday – Friday: 6:00am to 4:30pm HOW YOU WILL CONTRIBUTE: As an Installation Technician in our heavy bay, you will have a variety of responsibilities including MIG welding, fabrication, and some assembly work in the up-fit and installation of equipment on heavy-duty work truck builds. The role also involves diagnostic and repair work. You will need to read schematics, diagrams, blueprints, perform shop math, experience in MIG Welding, and ensure accurate installations and repairs. Knowledge of wiring and electrical systems and/or hydraulics is a plus. WHAT WE OFFER YOU: • Paid Time Off: Start accruing PTO with your very first paycheck., • Holiday Pay: Enjoy 11 paid holidays each year—no waiting period!, • Quarterly Retention Incentive Bonus: Earn $1 for every regular hour and $1.50 for every overtime hour worked, paid out quarterly., • Extra Paid Time Off: Get rewarded with additional PTO for excellent attendance., • Comprehensive Benefits Package: Includes Medical, Dental, Life, Disability, and more., • 401(k) Retirement Plan: Generous company match with immediate vesting., • Annual Fitness Reimbursement: Receive up to $250 each year to support your wellness goals., • Safety Gear Reimbursement: Get reimbursed for safety shoes and safety glasses., • Professional Development: Access tons of opportunities to grow your skills and advance your career., • And Much More! Discover even more perks when you join our team. WHAT THIS ROLE NEEDS (preferred): • Basic shop math & ability to interpret work instructions, diagrams & blueprints, • Hand dexterity and working knowledge of hand tools, • Must be willing to work in a team environment, • Previous experience in manufacturing setting, • Familiarity with weld, assembly processes, • Technical degree helpful and/or specialty certifications (i.e., welding, electrical, hydraulics), not required WORKING CONDITIONS: • Ability to lift/push up to 50 lbs., • Bending, lifting, and standing, • Exposure to noise and weld and grinding smoke at times Our focus on integrity, teamwork, and high performance creates an ideal work environment for every one of our employees. Discover our opportunities and come see all the ways you can do more at Douglas Dynamics. As an Equal Opportunity Employer, Douglas Dynamics, LLC does not discriminate against qualified applicants in hiring based on race, color, sex, age, sexual orientation, gender identity, national origin, disability or any other characteristic protected by law.

Job Description Steel Welder (MIG) St. Louis, MO 1st Shift | Monday-Friday | 7:00 AM - 3:30 PM Competitive Pay - Based on Experience Now Hiring Experienced Steel Welders! Wise Staffing is looking for MIG Welders with heavy steel fabrication experience for a leading manufacturer in St. Louis. Responsibilities • Perform MIG welding on heavy steel components., • Read and interpret blueprints and weld symbols., • Fabricate, fit, and assemble steel products., • Inspect finished welds for quality and accuracy., • Follow all company safety procedures.Qualifications, • 3-5 years of heavy steel welding experience., • Strong MIG welding skills., • Blueprint reading required., • Must be able to pass a weld test.Benefits, • First shift hours, • Long-term employment opportunity, • Competitive pay based on experience, • Opportunity to work with a respected manufacturing companyReady to put your welding skills to work? Apply today!

Job Description About PTS: Trusted, Responsive, and Nationwide Phillips Tank & Structure (PTS) is a growing, team-oriented, nationwide tank construction company with headquarters in Braddock, Pennsylvania, just outside of the City of Pittsburgh. We have over 190 employees and branch offices in Texas, California, Kentucky, and Hawaii. We specialize in designing, engineering, repairing, and constructing above-ground metal storage tanks and related structures, including welded tanks, bolted tanks, and geodesic domes. We have active projects in various industries, such as petroleum, power, chemical, and renewable fuels. At PTS, our commitment to our customers shapes everything we do. We have served companies across an array of industries, handling new tanks, repairs, and modifications. Our collective methodology, industry knowledge, and exhaustive range of abilities permit us to meet one-of-a-kind needs of our customers as they react to industry expectations. We believe in good quality and on-time delivery. We provide an excellent working relationship based on integrity and professionalism. Why Choose PTS? • Positive Work Culture: PTS employees experience a healthy blend of creativity, accountability, motivation, and improvement through team-based interactions with peers and other group members., • Professional Development: PTS is a growing company with many opportunities for advancement. PTS' systems-based approach to training and development helps employees quickly find the path to success in our company., • Intellectual Satisfaction: Being part of a team that executes unique and challenging projects throughout the country and actually builds something is an exciting endeavor. Our Core Principles • Service: The primary expectation for all employees at PTS is to focus on service. We are called to serve our customers as well as our co-workers and suppliers. We endeavor to build a cohesive team of employees who care about the well-being of the group., • Planning and Problem Solving: Planning and problem solving should be utilized to achieve productivity. We will strive every day to be organized and efficient in our approach. We will always look for better ways to achieve results rather than propagating inefficient or inaccurate methods., • Personal Development: Every employee should assist in the development of co-workers just as each employee should pursue their own personal development. Mentor and teammate relationships lay the groundwork for future growth and rewards. We are currently looking to hire a full-time Tank Builder / Welder (Nationwide) Day to Day Duties: • Performing arc and torch cutting and gouging., • Using generators, compressors, tuggers, blowers, grinders, and other power and air tools., • Welding plate with 7018, 7024 and 6010 stick (SMAW), flux core (FCAW), and submerged arc automatic machines (3 o’clock and “goat”/tractor)., • Using come-alongs, hydraulic jacks, hoists, air bags, winches, and other lifting equipment., • Using tank shell buggies, tank scaffolding, tank ladders, and other specialty equipment., • Performing vacuum box tests, oil tests, dye penetrant tests, and other non-destructive quality examinations., • Using gas monitors, fresh air kits, respirators, emergency rescue kits, and other safety equipment., • Operating forklifts, man lifts, boom lifts, and other large lifting equipment., • Knowledge of crane operations (including rigging and signaling), • Reading detailed erection and fabrication drawings., • Planning the sequence and methods of fitting up, welding, repairing, and constructing tanks., • Completing job safety analysis, safety audits, site-specific training, and other safety training., • Follow directions and work professionally with other crew members., • Other duties as assigned. Requirements, • Have great communication and organization skills., • The ability to solve problems and suggest improvements to our systems., • Have excellent attendance and show up to work on time every day., • The willingness to learn., • Be at least 18 years old., • Be able to lift 50 lbs., • Have a high school diploma or equivalent., • Be eligible to work in the United States., • Be willing to authorize background checks., • Have no criminal convictions for dishonesty, sexual misconduct, violence, or acts of terrorism., • Have a valid driver’s license., • Be willing to authorize motor vehicle driving record checks., • Be willing to submit to pre-hire, random, and post-incident drug and alcohol testing., • Ability to weld is a plus. Benefits: • Competitive Pay with annual reviews, • Health, Dental and Vision insurance, • 401k with company match, • Great culture of teamwork, learning and development., • You’ll be part of a team where YOU matter To Apply: If interested, complete the job application from our website at www.phillipstank.com/careers. We are an Equal Employment Opportunity employer. Powered by JazzHR 0YI6uMTLil

Job Description Title: Quality Control Manager Location: Columbia, MO Region Position Overview A growing industrial manufacturing organization is seeking a Quality Control Manager to lead site-level quality operations within a fabrication and welding environment. This individual will be responsible for overseeing the Quality Management System (QMS), maintaining compliance with customer and industry standards, and driving continuous improvement across manufacturing operations. This is a hands-on leadership role overseeing quality personnel while partnering closely with operations, engineering, and production teams to support manufacturing performance, audit readiness, and welding quality compliance. Key Responsibilities • Lead and develop Quality Inspectors, Welding Inspectors, and Quality personnel while ensuring inspection coverage across operations, • Manage incoming, in-process, and final inspection programs, • Develop, implement, and maintain quality procedures, inspection plans, and documentation systems, • Lead management review meetings and present quality metrics, audit findings, and improvement plans to leadership, • Ensure compliance with customer specifications, fabrication drawings, welding procedures, and applicable industry standards, • Write, review, and maintain WPS, PQR, and Welder Qualification documentation, • Lead root cause analysis and corrective action activities related to nonconformances and quality issues, • Coordinate with production, engineering, purchasing, and operations teams to resolve manufacturing quality concerns, • Manage calibration systems for inspection and measurement equipment, • Lead internal, external, and customer audit activities while ensuring timely closure of findings, • Drive continuous improvement initiatives focused on reducing scrap, rework, delays, and quality escapes, • Maintain quality records, reporting systems, and compliance documentation, • Serve as a primary quality contact for customers, auditors, and third-party inspectors, • Support plant safety initiatives and maintain compliance with company safety standards Qualifications Education • High school diploma or equivalent required, • Associate’s degree or bachelor’s degree in Engineering, Manufacturing, Quality, or related field preferred Experience • 5+ years of quality experience within a manufacturing or fabrication environment, • 3+ years of leadership or supervisory experience managing quality personnel, • Experience leading internal and external audits, • Hands-on experience within welding, fabrication, or metal manufacturing operations, • Experience with management review processes, KPI reporting, and corrective action systems Certifications (Preferred) • Certified Welding Inspector (CWI) certification strongly preferred Technical Skills • Strong understanding of fabrication, welding, and manufacturing quality systems, • Ability to read and interpret blueprints, fabrication drawings, and welding symbols, • Experience with root cause analysis, audits, CAPA, and KPI reporting, • Proficiency with inspection tools, spreadsheets, and quality documentation systems Benefits • Health Insurance, • Life Insurance, • Paid Time Off If you are interested in this position, please apply here or send your resume to matthew@mrrecruiter.com. Equal Opportunity Employer Disclaimer This organization is an Equal Opportunity Employer and is committed to creating an inclusive and diverse workplace. All qualified applicants will receive consideration for employment without regard to race, color, religion, sex, sexual orientation, gender identity or expression, national origin, age, disability status, genetic information, protected veteran status, or any other characteristic protected by applicable law. Employment decisions are based solely on qualifications, merit, and business needs.

Job Description Job Summary Automation Services is seeking a skilled Welder to support the repair, restoration, and fabrication of industrial control valve components and sealed instrumentation systems. This position requires experience with MIG and TIG welding, metal finishing, and precision fabrication to restore critical components to OEM specifications. The ideal candidate is detail-oriented, takes pride in quality workmanship, and enjoys working in a hands-on industrial manufacturing environment. Responsibilities: • Perform MIG and TIG weld buildup to repair worn, damaged, or washed-out control valve components, including balls, plugs, discs, shafts, bonnets, and related parts., • Grind, sand, machine, and polish repaired components to restore OEM dimensions and surface finishes., • Operate MIG bore welding equipment to repair valve bonnets and other components., • Weld diaphragms for sealed pressure transmitter systems using an automated welding lathe., • Fabricate sealed instrumentation systems according to work orders and engineering specifications., • Perform vacuum leak testing to verify the integrity of fabricated sealed systems., • Manufacture and maintain inventory of standard fabricated components such as seals, brackets, capsules, and other production parts., • Fabricate shop fixtures, carts, tooling, and miscellaneous support equipment as needed., • Safely operate MIG and TIG welders, drill presses, grinders, oxy-acetylene equipment, and other fabrication tools., • Monitor and maintain inventory levels of welding consumables, grinding materials, and related shop supplies., • Follow all company safety procedures and maintain a clean, organized work area., • Perform other duties as assigned. Qualifications: • High school diploma or GED preferred., • Minimum of 1 year of MIG and TIG welding experience in a manufacturing, industrial, or fabrication environment., • Ability to successfully pass a 2G welding certification., • Experience repairing or fabricating precision metal components is preferred., • Experience with industrial valves, instrumentation, or rotating equipment is a plus. Required Skills • Proficiency in MIG and TIG welding techniques., • Experience welding a variety of metals, including: Mild Steel, 316 Stainless Steel, Hastelloy, Stellite Alloy 6, • Ability to read work instructions, drawings, and specifications., • Strong mechanical aptitude and attention to detail., • Ability to safely operate fabrication equipment and hand tools., • Excellent organizational skills and commitment to producing high-quality work. Physical Requirements • Ability to stand for extended periods (6–8 hours per shift)., • Ability to frequently lift up to 30 pounds., • Ability to safely perform repetitive welding, grinding, lifting, and material handling tasks., • Must be able to work safely in an industrial manufacturing environment while wearing required PPE.